SSL_shutdown(3) OpenSSL SSL_shutdown(3)NAMESSL_shutdown - shut down a TLS/SSL connection
int SSL_shutdown(SSL *ssl);
DESCRIPTIONSSL_shutdown() shuts down an active TLS/SSL connection. It sends the
"close notify" shutdown alert to the peer.
NOTESSSL_shutdown() tries to send the "close notify" shutdown alert to the
peer. Whether the operation succeeds or not, the SSL_SENT_SHUTDOWN
flag is set and a currently open session is considered closed and good
and will be kept in the session cache for further reuse.
The shutdown procedure consists of 2 steps: the sending of the "close
notify" shutdown alert and the reception of the peer's "close notify"
shutdown alert. According to the TLS standard, it is acceptable for an
application to only send its shutdown alert and then close the underly‐
ing connection without waiting for the peer's response (this way
resources can be saved, as the process can already terminate or serve
another connection). When the underlying connection shall be used for
more communications, the complete shutdown procedure (bidirectional
"close notify" alerts) must be performed, so that the peers stay syn‐
SSL_shutdown() supports both uni- and bidirectional shutdown by its 2
When the application is the first party to send the "close notify"
alert, SSL_shutdown() will only send the alert and the set the
SSL_SENT_SHUTDOWN flag (so that the session is considered good and will
be kept in cache). SSL_shutdown() will then return with 0. If a unidi‐
rectional shutdown is enough (the underlying connection shall be closed
anyway), this first call to SSL_shutdown() is sufficient. In order to
complete the bidirectional shutdown handshake, SSL_shutdown() must be
called again. The second call will make SSL_shutdown() wait for the
peer's "close notify" shutdown alert. On success, the second call to
SSL_shutdown() will return with 1.
If the peer already sent the "close notify" alert and it was already
processed implicitly inside another function (SSL_read(3)), the
SSL_RECEIVED_SHUTDOWN flag is set. SSL_shutdown() will send the "close
notify" alert, set the SSL_SENT_SHUTDOWN flag and will immediately
return with 1. Whether SSL_RECEIVED_SHUTDOWN is already set can be
checked using the SSL_get_shutdown() (see also SSL_set_shutdown(3)
It is therefore recommended, to check the return value of SSL_shut‐
down() and call SSL_shutdown() again, if the bidirectional shutdown is
not yet complete (return value of the first call is 0). As the shutdown
is not specially handled in the SSLv2 protocol, SSL_shutdown() will
succeed on the first call.
The behaviour of SSL_shutdown() additionally depends on the underlying
If the underlying BIO is blocking, SSL_shutdown() will only return once
the handshake step has been finished or an error occurred.
If the underlying BIO is non-blocking, SSL_shutdown() will also return
when the underlying BIO could not satisfy the needs of SSL_shutdown()
to continue the handshake. In this case a call to SSL_get_error() with
the return value of SSL_shutdown() will yield SSL_ERROR_WANT_READ or
SSL_ERROR_WANT_WRITE. The calling process then must repeat the call
after taking appropriate action to satisfy the needs of SSL_shutdown().
The action depends on the underlying BIO. When using a non-blocking
socket, nothing is to be done, but select() can be used to check for
the required condition. When using a buffering BIO, like a BIO pair,
data must be written into or retrieved out of the BIO before being able
SSL_shutdown() can be modified to only set the connection to "shutdown"
state but not actually send the "close notify" alert messages, see
SSL_CTX_set_quiet_shutdown(3). When "quiet shutdown" is enabled,
SSL_shutdown() will always succeed and return 1.
The following return values can occur:
1 The shutdown was successfully completed. The "close notify" alert
was sent and the peer's "close notify" alert was received.
0 The shutdown is not yet finished. Call SSL_shutdown() for a second
time, if a bidirectional shutdown shall be performed. The output
of SSL_get_error(3) may be misleading, as an erroneous
SSL_ERROR_SYSCALL may be flagged even though no error occurred.
-1 The shutdown was not successful because a fatal error occurred
either at the protocol level or a connection failure occurred. It
can also occur if action is need to continue the operation for non-
blocking BIOs. Call SSL_get_error(3) with the return value ret to
find out the reason.
SEE ALSOSSL_get_error(3), SSL_connect(3), SSL_accept(3), SSL_set_shutdown(3),
SSL_CTX_set_quiet_shutdown(3), SSL_clear(3), SSL_free(3), ssl(3),
bio(3)0.9.7d 2002-12-01 SSL_shutdown(3)