atlc(1)atlc(1)NAMEatlc - an Arbitrary Transmission Line Calculator
SYNOPSISatlc [-C] [-s] [-S] [-v] [-c cutoff] [-d rrggbb=Er] [-i factor] [-i
prefix] [-t threads] [-r rate_multiplier] bitmapfile
WARNING
This man page is not a complete set of documentation - the complexity
of the atlc project makes man pages not an ideal way to document it,
although out of completeness, man pages are produced. The best docu‐
mentation that was current at the time the version was produced should
be found on your hard drive, usually at
/usr/local/share/atlc/docs/html-docs/index.html
although it might be elsewhere if your system administrator chose to
install the package elsewhere. Sometimes, errors are corrected in the
documentation and placed at http://atlc.sourceforge.net/ before a new
release of atlc is released. Please, if you notice a problem with the
documentation - even spelling errors and typos, please let me know.
DESCRIPTIONatlc is a finite difference program that is used to calculate the prop‐
erties of a two-conductor electrical transmission line of arbitrary
cross section. It is used whenever there are no analytical formula
known, yet you still require an answer. It can calculate:
The impedance Zo (in Ohms)
The capacitance per unit length (pF/m)
The inductance per unit length (nF/m)
The velocity of propagation v (m/s)
The velocity factor, v/c, which is dimensionless.
A bitmap file (usually with the extension .bmp or .BMP) is drawn in a
graphics package such as Gimp available from http://www.gimp.org. The
bitmap file must be saved as a 24-bit (16,777,216 colour) uncompqessed
file. The colours used in the bitmap indicate whether the region is a
conductor (pure red, pure green or pure blue) or a dielectric (anything
else). Pure white is assumed to be a vacuum dielectric, but other
colours have different meanings. See COLOURS below for precise defini‐
tions of the colours.
OPTIONS-C
print copyright, licensing and copying information.
-s
Skip writing the Ex, Ey, E, V, U and Er bitmap (.bmp) files -S
Skip writing the Ex, Ey, E, V, U and Er binary (.bin) files
-v
makes the output more verbose/talkative.
-c cutoff
Sets the convergence criteria of the finite difference program. The
default is 0.0001, meaning two separate iterations must be within 01%
for the program to stop iterating. Setting to a smaller positive number
gives more accuracy, but takes longer.
-d rrggbb=Er
is used to indicate the colour 0xrrggbb in the bitmap is used to repre‐
sent a material with permittivity Er. See also COLOURS below
-i factor
is used to lighten or darken the .bmp electric field profile images
produced by atlc. Set factor > 2 to lighten or between 1 and 2 to
darken.
-r ratemultiplier
Sets the parameter 'r' used internally when computing the voltage at a
point w,h. The default, which is (as of version 3.0.0) 1.95, results
in what is believed to be optimal results. Setting to 1.0 will avoid
the use of the fast convergence method, which is generally not a good
idea.
-p prefix
Adds 'prefix', which is usually a directory name, in front of the out‐
put files.
COLOURS
The 24-bitmaps that atlc uses have 8 bits assigned to represent the
amount of red, 8 for blue and 8 for green. Hence there are 256 levels
of red, green and blue, making a total of 256*256*256=16777216 colours.
Every one of the possible 16777216 colours can be defined precisely by
the stating the exact amount of red, green and blue, as in:
red = 255,000,000 or 0xff0000
green = 000,255,000 or 0x00ff00
blue = 000,000,255 or 0x0000ff
black = 000,000,000 or 0x000000
white = 255,255,255 or 0xffffff
Brown = 255,000,255 or 0xff00ff
gray = 142,142,142 or 0x8e8e8e
Some colours, such as pink, turquiose, sandy, brown, gray etc may mean
slightly different things to different people. This is not so with
atlc, as the program expects the colours below to be exactly defined as
given. Whether you feel the colour is sandy or yellow is up to you, but
if you use it in your bitmap, then it either needs to be a colour
reconised by atlc, or you must define it with a command line option
(see OPTIONS).
red = 255,000,000 or 0xFF0000 is the live conductor.
green = 000,255,000 or 0x00FF00 is the grounded conductor.
blue = 000,000,255 or 0x0000FF is the negative conductor
All bitmaps must have the live (red) and grounded (green) conductor.
The blue conductor is used to indicate a negative conductor, is needed
when the program is used to analyse directional couplers.
The following dielectrics are reconised by atlc:
white 255,255,255 or 0xFFFFFF as Er=1.0 (vacuum)
pink 255,202,202 or 0xFFCACA as Er=1.0006 (air)
L. blue 130,052,255 or 0x8235EF as Er=2.1 (PTFE)
Mid gray 142,242,142 or 0x8E8E8E as Er=2.2 (duroid 5880)
mauve 255.000,255 or 0xFF00FF as Er=2.33 (polyethylene)
yellow 255,255,000 or 0xFFFF00 as Er=2.5 (polystyrene)
sandy 239,203,027 or 0xEFCC1A as Er=3.3 (PVC)
brown 188,127,096 or 0xBC7F60 as Er=3.335 (epoxy resin)
L. yellow 223,247,136 or 0xDFF788 as Er=3.7 (FR4 PCB)
Turquoise 026,239,179 or 0x1AEFB3 as Er=4.8 (glass PCB)
Dark gray 142,142,142 or 0x696969 as Er=6.15 (duroid 6006)
L. gray 240,240,240 or 0xDCDCDC as Er=10.2 (duroid 6010)
D. orange 213,160,067 or 0xD5A04D as Er=100.0 (mainly for test pur‐
poses)
EXAMPLES
Here are a few examples of the use of atlc. Again, see the html docu‐
mentation in atlc-X.Y.Zocsl-docs, the documentation on your system
(normally at /usr/local/share/atlc/docs/html-docs/index.html ) or
online at http://atlc.sourceforge.net for examples.
ex_1 % atlc coax2.bmp
This is a simple example (ex_1), in which the geometry of a transmis‐
sion line is defined in coax2.bmp. In this example, only the predefined
dielectrics (Er =1.0, 1.0006, 2.1, 2.2, 2.33, 2.5, 3.3, 3.335, 3.7,
4.8, 6.15 or 10.2) could have been used in the bitmap, which would have
been done with one of 13 different colours. white (0xFFFFFF) for
Er=1.0, pink (0xFFCACA) for 1.0006 etc. No other colour (dielectric)
could have been used, since it was not specified with the -d option.
ex_2 % atlc-d f9e77d=2.43 somefile.bmp
In ex_2, a dielectric with Er=2.43 was wanted. A colour with the RGB
values of 0xF9E7&d was used. The -d option tells atlc what Er this
colour refers to.
ex_3 % atlc-v coax2.bmp
In ex_3, atlc has been instructed to print the results of intermediate
calculations to stdout. Normally, only the final result is printed.
Using -vv even more information may be produced, but this is really of
only use to the developer of the project.
FILES
bitmapfile.bmp
Original bitmap file. Must be 24-bit colour uncompressed.
bitmapfile.Ex.bmp
X-component of E-field as a bitmap. Red=+dV/dx, blue =-dV/dx
bitmapfile.Ey.bmp
y-component of E-field as a bitmap. Red=+y, blue =-y
bitmapfile.E.bmp
E-field, as E=sqrt(Ex^2+Ey^2).
bitmapfile.V.bin
Voltage as a bitmap, red= positive, blue =negative.
bitmapfile.Er.bin
Bitmap showing the permittivity as a grayscale. Lighter is a higher
permittivity.
bitmapfile.U.bmp
Energy.
In addition to the bitmaps, the data is also saved in binary files.
All the saved binary files (.bin's) are saved as a double precision
number for each of the pixels. The first double is the top left, the
last the bottom right. If the original image has width W and height H,
the saved binary files will be W-1 by H-1.
All the saved bitmap files are 24-bit uncompressed, just like the input
files.
SEE ALSOatlc(1)create_bmp_for_circ_in_circ(1)create_bmp_for_circ_in_rect(1)create_bmp_for_microstrip_coupler(1)create_bmp_for_rect_cen_in_rect(1)create_bmp_for_rect_cen_in_rect_coupler(1) cre‐
ate_bmp_for_rect_in_circ(1)create_bmp_for_rect_in_rect(1) cre‐
ate_bmp_for_stripline_coupler(1) create_bmp_for_symmetri‐
cal_stripline(1)design_coupler(1) find_optimal_dimen‐
sions_for_microstrip_coupler(1)readbin(1)
http://atlc.sourceforge.net - Home page
http://sourceforge.net/projects/atlc - Download area
atlc-X.Y.Z/docs/html-docs/index.html - HTML docs
atlc-X.Y.Z/docs/qex-december-1996/atlc.pdf - theory paper
atlc-X.Y.Z/examples - examples
Dr. David Kirkby atlc-4.4.2 10th Sept 2003 atlc(1)
