atmconfig man page on FreeBSD

Man page or keyword search:  
man Server   9747 pages
apropos Keyword Search (all sections)
Output format
FreeBSD logo
[printable version]

ATMCONFIG(8)		  BSD System Manager's Manual		  ATMCONFIG(8)

     atmconfig — ATM configuration tool

     atmconfig [-htv] [command [sub-command [...]]] [options] [arg ...]

     The atmconfig tool is used to configure the Netgraph ATM network sub-sys‐

     The command line of atmconfig generally consists of common options fol‐
     lowed by a command string, optionally followed by sub-command strings,
     optional command specific options and command specific arguments.	Com‐
     mands and sub-commands as well as command specific options may be abbre‐
     viated as long as there is only one match possible.

   Common Options
     The following common options change the overall behaviour of atmconfig:

     -h	     Print a very short usage info and exit.

     -t	     Several show-type commands output a header and then several lines
	     of information.  If this option is given, the header is omitted,
	     simplifying the parsing of the output.

     -v	     Be more verbose.

   Obtaining Help
     The help command has a number of useful sub-commands.

     To get general help use:
	   atmconfig help

     To get a list of available commands use:
	   atmconfig help commands

     To get a list of available sub-commands use:
	   atmconfig help command

     or (if there are deeper levels of sub-commands):
	   atmconfig help command sub-command ...

     To get a list of options and arguments for a command use:
	   atmconfig help command sub-command ...
     (given that there are no further sub-command levels).

     To get a list of common options use:
	   atmconfig help options

   The diag Command
     The diag command allows the inspection of the ATM interfaces on the local
     host and the modification of device parameters.  Sub-commands are: list
     (print a list of interfaces), config (print hardware configuration), phy
     (access PHY chip), stats (print statistics) and vcc (print list of VCCs).

     atmconfig diag list
	     This sub-command lists all ATM interfaces in the system.  It
	     takes no options or arguments.

     atmconfig diag config [-atm] [-hardware] [device ...]
	     This command prints the configuration of ATM interfaces.  If no
	     device is given, all devices are listed, otherwise only the spec‐
	     ified devices.  The option -atm instructs the command to print
	     ATM layer configuration parameters like the number of VCI and VPI
	     bits, whereas the -hardware option requests card specific infor‐
	     mation like the vendor or the serial number.  If none of the
	     options is given, the defaults is to assume -atm.

     atmconfig diag phy print [-numeric] device
	     This command prints the PHY registers in a (potential) human com‐
	     prehensible format.  If -numeric is given, the format is hex
	     bytes.  Otherwise, textual representation will be printed.

     atmconfig diag phy show [device ...]
	     This sub-command prints static information about the PHY device
	     used in the ATM card like the type of the PHY and the media.

     atmconfig diag phy set device reg mask val
	     This sub-command allows one to change bits in PHY registers.
	     This should be used with great care.  The bits of the given PHY
	     chip register for which the corresponding bit in mask is one are
	     set to the values of the corresponding bits in val.  All register
	     bits that have a zero in mask are written back with their origi‐
	     nal value.

     atmconfig diag phy stats [-clear] device
	     Print the PHY statistics for the given device.  When the optional
	     -clear is given, the statistics are cleared atomically.

     atmconfig diag vcc [-abr] [-channel] [-traffic] [device]
	     Retrieve the list of currently active channels on either all or
	     the specified interfaces.	For each channel, the following infor‐
	     mation is printed depending on the options (default is -channel).

	     -abr      Print ABR specific traffic parameters: ICR, TBE, NRM,
		       TRM, ADTF, RIF, RDF, CDF.

	     -channel  Print basic information: VPI, VCI, AAL, traffic type,
		       MTU and flags.

	     -traffic  Print traffic parameters: PCR, SCR, MBS, MCR.

     atmconfig diag stats device
	     Print driver specific statistics.

   The natm Command
     The natm command is used to change natmip(4) routes on the local host.
     The sub-commands for the routing table are: add (to add a new route),
     delete (to delete an existing route) and show (to print the currently
     installed NATM routes).

     atmconfig natm add dest device vpi vci encaps
     atmconfig natm add dest device vpi vci encaps ubr [pcr]
     atmconfig natm add dest device vpi vci encaps cbr pcr
     atmconfig natm add dest device vpi vci encaps vbr pcr scr mbs
     atmconfig natm add dest device vpi vci encaps abr pcr mcr icr tbe nrm trm
	     adtf rif rdf cdf
	     Add a new route to the routing table.  The destination address
	     (the address on the other end of the link) is given in dest.  The
	     device, vpi and vci arguments are the name of the ATM device and
	     the VPI and VCI values for the link.  The encaps argument may be
	     either AAL5 or LLC/SNAP both of which specify AAL5 encapsulation,
	     the first one without additional encapsulation, the second one
	     with LLC/SNAP headers.  The first two forms of the command add an
	     UBR (unspecified bit rate) channel, where the second form allows
	     the optional specification of a peak cell rate (PCR).  The third
	     form adds a CBR (constant bit rate) channel where a PCR must be
	     given.  The fourth form adds a VBR (variable bit rate) channel.
	     The arguments are the peak cell rate, the sustainable cell rate
	     and the maximum bursts size.  The last form of the command adds
	     an ABR (available bit rate) channel.

     atmconfig natm delete dest
     atmconfig natm delete device vpi vci
	     This commands deletes an NATM route.  The route may be specified
	     either by the destination address or by the device, vpi and vci

     atmconfig natm show
	     List all NATM routes.

     natm(4), natmip(4), atm(8)

     Hartmut Brandt ⟨⟩

BSD				August 11, 2003				   BSD

List of man pages available for FreeBSD

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
Vote for polarhome
Free Shell Accounts :: the biggest list on the net