avmcapictrl man page on Oracle

Printed from http://www.polarhome.com/service/man/?qf=avmcapictrl&af=0&tf=2&of=Oracle

AVMCAPICTRL(8)		  Linux System Administration		AVMCAPICTRL(8)

NAME
       avmcapictrl - Add, reset or remove active AVM cards and load firmware

SYNOPSIS
       avmcapictrl add <portbase> <irq> <type>
       avmcapictrl load <bootcode> [<contrnr> [<protocol>
	   [P2P | <dn1>:<spid1> [<dn2>:<spid2>]]]]
       avmcapictrl reset [contrnr]
       avmcapictrl remove [contrnr]
       avmcapictrl trace [contrnr] [off|short|on|full|shortnodata|nodata]
       avmcapictrl  addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ]
       ]

DESCRIPTION
       avmcapictrl is used to register active AVM ISA cards kernelcapi	system
       and  therewith  to  the	isdn  system.  You  need it also to upload the
       firmware to any active AVM card. If an error occurred please also check
       the kernel error messages by using the command dmesg(8).

COMMANDS
       add <portbase> <irq> <type>
	    is used to add a ISA card to the kernel-capi2.0 system.  The port‐
	    base can have the values 0x150, 0x250, 0x300 and 0x340 for the  B1
	    ISA	 cards,	 look  at the jumper on the card.  For a T1-ISA (HEMA)
	    card you can select an wide range of ports.
	    irq can be selected from the following values:
	    3, 4, 5, 6, 7, 9, 10, 11, 12 and 15.
	    type can be B1 or T1.

       load <bootcode> [<contrnr> [<protocol>
	    [P2P |  <dn1>:<spid1>  [<dn2>:<spid2>]]]]  is  used	 to  load  the
	    firmware  to  a card bootcode is a t4-file. The actual versions of
	    the t4-files for the different d-channel protocols can be found at
	    ftp://ftp.avm.de/cardware/b1/linux/firmware.
	    You	 need  different  t4-files  for different d channel protocols:
	    b1-1tr6.t4 for 1TR6, b1.t4 for DSS1 and
	    b1-usa.t4 for 5ESS and NI1 (DSS1 is also supported).
	    For M1/M2 PCMCIA cards you need m1-s10.t4 or m1-s4.t4 depending on
	    the handy type used.
	    contrnr is the number of the controller (card) starting from 1.
	    protocol can be DSS1, CT1, VN3, AUSTEL, 5ESS or NI1.
	    P2P point to point
	    DN1:SPID1  DN2:SPID2 is for the North American 5ESS and NI1 proto‐
	    cols.

       reset [contrnr]
	    is used to reset a card if loading has failed.  This function only
	    make sense if card is not successfully loaded.
	    contrnr is the number of the controller (card) starting from 1.

       remove [contrnr]
	    is used to remove a card previous added. You can also remove auto‐
	    matic added cards (for example a B1-PCI card).
	    contrnr is the number of the controller (card) starting from 1.

       trace [contrnr] [off|short|on|full|shortnodata|nodata]
	    is used to trace CAPI2.0 messages. The trace will be done as  ker‐
	    nel messages, see dmesg(8).
	    contrnr is the number of the controller (card) starting from 1.
	    off switch tracing off
	    short switch one line per CAPI2.0 message tracing on
	    on | full switch on full decode tracing
	    shortnodata	 switch	 on  line  per CAPI2.0 message tracing on, but
	    exclude DATA_B3_IND and DATA_B3_REQ messages.
	    on | full switch on full decode tracing, but  exclude  DATA_B3_IND
	    and DATA_B3_REQ messages.

       addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]
	    is used to add a card, this is more generic than add.
	    driver currently b1isa or t1isa
	    portbase can have the values 0x150, 0x250, 0x300 and 0x340 for the
	    b1isa driver, look at the jumper on the card.   For	 t1isa	driver
	    you can select an wide range of ports.
	    irq	 can  be selected from the following values: 3, 4, 5, 6, 7, 9,
	    10, 11, 12 and 15.
	    membase memory address if needed by driver
	    cardnr only useful with driver t1isa

AUTHOR
       Carsten Paeth <calle@calle.in-berlin.de>

SEE ALSO
       ttyI(4), isdnctrl(8), isdninfo(4).  dmesg(8).  syslogd(8).

4th Berkeley Distribution	  2000/01/28			AVMCAPICTRL(8)
[top]

List of man pages available for Oracle

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net