BOOT_I386(8) OpenBSD System Manager's Manual (i386) BOOT_I386(8)NAMEboot_i386 - i386 system bootstrapping procedures
The PC AT clones will perform a POST (Power On Self Test) upon being
booted cold. This test will find and initialize memory, keyboard, and
other devices. It will search for and initialize any extension ROMs that
are present, and then attempt to boot the operating system from an
available boot drive. Failing this, older IBM systems come up in ROM
The newer PC AT clones attempt to boot off the drive specified in the
BIOS setup, or if it is an older BIOS, it will start with checking for a
disk in floppy drive A (otherwise known as drive 0) first, and failing
that, attempt to boot the hard disk C (otherwise known as hard disk
controller 1, drive 0).
The BIOS loads the first block (at physical location: track 0, head 0,
sector 1) off the boot device into memory, and if the last two bytes in
the block match the signature 0xAA55, the BIOS considers the block a
valid bootable drive. The BIOS then proceeds to call the machine code
program in this block. If the BIOS is current, it will also pass the
boot drive to the boot block in register %dl.
There are two different types of boot blocks on devices. There is the
MBR (master boot record) and the PBR (partition boot record). A
digression into a little piece of history will quickly give light as to
why this is so. In the beginning, the PC ``architecture'' came with
single or dual floppy drives, and no hard drives. The only type of
bootable sectors on any device were the PBRs. They were responsible for
loading the rest of the operating system from the correct device. When
hard disks came out, it was felt that such a huge space should be able to
be partitioned into separate drives, and this is when the MBR was
The MBR relocates itself upon being loaded and invoked by the BIOS.
Embedded within the MBR is a partition table, with four partition table
entries. The MBR code traverses this table (which was loaded with the
MBR by the BIOS), looking for an active entry, and then loads the MBR or
PBR from the disk location specified by the partition table entry. So in
reality, the MBR is nothing more than a fancy chaining PBR.
Note: The MBR could load another MBR, which is the case when you are
booting off an extended partition. In other words, the first block of an
extended partition is really an MBR, which will then load the
corresponding MBR or PBR out of its extended partition's partition table.
WARNING: This portion of the ``PC BIOS Architecture'' is a mess, and a
The PC BIOS has an API to manipulate any disk that the BIOS happens to
support. This interface uses 10 bits to address the cylinder, 8 bits to
address the head, and 6 bits to address the sector of a drive. This
restricts any application using the BIOS to being able to address only
1024 cylinders, 256 heads, and 63 (since the sectors are 1 based) sectors
on a disk. These limitations proved to be fine for roughly 3 years after
the debut of hard disks on PC computers.
Many (if not all) newer drives have many more cylinders than the BIOS API
can support, and likely more sectors per track as well. To allow the
BIOS the ability of accessing these large drives, the BIOS would
``re-map'' the cylinder/head/sector of the real drive geometry into
something that would allow the applications using the BIOS to access a
larger portion of the drive, still using the restricted BIOS API.
The reason this has become a problem is that any modern OS will use its
own drivers to access the disk drive, bypassing the BIOS completely.
However, the MBR, PBR, and partition tables are all still written using
the original BIOS access methods. This is for backwards compatibility to
the original IBM PC!
So the gist of it is, the MBR, PBR, and partition table need to have BIOS
geometry offsets and cylinder/head/sector values for them to be able to
load any type of operating system. This geometry can, and likely will,
change whenever you move a disk from machine to machine, or from
controller to controller. They are controller and machine specific.
Boot process options
On most OpenBSD systems, booting OpenBSD from the BIOS will eventually
load the OpenBSD-specific i386 bootstrapping code. This versatile
program is described in a separate document, boot(8). Other
bootstrapping software may be used, and can chain-load the OpenBSD
bootstrapping code, or directly load the kernel. In the latter case,
refer to your bootloader documentation to know which options are
Abnormal system termination
In case of system crashes, the kernel will usually enter the kernel
debugger, ddb(4), unless it is not present in the kernel, or it is
disabled via the ddb.panic sysctl. Upon leaving ddb, or if ddb was not
entered, the kernel will halt the system if it was still in device
configuration phase, or attempt a dump to the configured dump device, if
possible. The crash dump will then be recovered by savecore(8) during
the next multi-user boot cycle. It is also possible to force other
behaviours from ddb.
/bsd default system kernel
/bsd.sp single processor capable kernel
/bsd.mp multiprocessor capable kernel
/bsd.rd standalone installation kernel, suitable for disaster
/usr/mdec/mbr system MBR image
/usr/mdec/biosboot system primary stage bootstrap (PBR)
/usr/mdec/boot system second stage bootstrap (usually also installed
/usr/mdec/pxeboot PXE bootstrap
SEE ALSOddb(4), boot(8), halt(8), init(8), installboot(8), pxeboot(8), reboot(8),
The ``PC BIOS Architecture'' makes this process very prone to weird and
wonderful interactions between different operating systems.
There is no published standard to the MBR and PBR, which makes coding
these a nightmare.
OpenBSD 4.9 August 10, 2010 OpenBSD 4.9