CRON(8) System Administration CRON(8)NAME
crond - daemon to execute scheduled commands
crond [-c | -h | -i | -n | -p | -P | -s | -m<mailcommand>]
crond -x [ext,sch,proc,pars,load,misc,test,bit]
Cron is started from /etc/rc.d/init.d or /etc/init.d when classical
sysvinit scripts are used. In case systemd is enabled, then unit file
is installed into /lib/systemd/system/crond.service and daemon is
started by systemctl start crond.service command. It returns immedi‐
ately, thus, there is no need to need to start it with the '&' parame‐
Cron searches /var/spool/cron for crontab files which are named after
accounts in /etc/passwd; The found crontabs are loaded into the memory.
Cron also searches for /etc/anacrontab and any files in the /etc/cron.d
directory, which have a different format (see crontab(5)). Cron exam‐
ines all stored crontabs and checks each job to see if it needs to be
run in the current minute. When executing commands, any output is
mailed to the owner of the crontab (or to the user specified in the
MAILTO environment variable in the crontab, if such exists). Any job
output can also be sent to syslog by using the -s option.
There are two ways how changes in crontables are checked. The first
method is checking the modtime of a file. The second method is using
the inotify support. Using of inotify is logged in the /var/log/cron
log after the daemon is started. The inotify support checks for
changes in all crontables and accesses the hard disk only when a change
When using the modtime option, Cron checks its crontables' modtimes
every minute to check for any changes and reloads the crontables which
have changed. There is no need to restart Cron after some of the
crontables were modified. The modtime option is also used when inotify
can not be initialized.
Cron checks these files and directories:
system crontab. Nowadays the file is empty by default. Origi‐
nally it was usually used to run daily, weekly, monthly jobs.
By default these jobs are now run through anacron which reads
/etc/anacrontab configuration file. See anacrontab(5) for more
directory that contains system cronjobs stored for different
directory that contains user crontables created by the crontab
Note that the crontab(1) command updates the modtime of the spool
directory whenever it changes a crontab.
Daylight Saving Time and other time changes
Local time changes of less than three hours, such as those caused by
the Daylight Saving Time changes, are handled in a special way. This
only applies to jobs that run at a specific time and jobs that run with
a granularity greater than one hour. Jobs that run more frequently are
If time was adjusted one hour forward, those jobs that would have run
in the interval that has been skipped will be run immediately. Con‐
versely, if time was adjusted backward, running the same job twice is
Time changes of more than 3 hours are considered to be corrections to
the clock or the timezone, and the new time is used immediately.
It is possible to use different time zones for crontables. See
crontab(5) for more information.
PAM Access Control
Cron supports access control with PAM if the system has PAM installed.
For more information, see pam(8). A PAM configuration file for crond
is installed in /etc/pam.d/crond. The daemon loads the PAM environment
from the pam_env module. This can be overridden by defining specific
settings in the appropriate crontab file.
OPTIONS-h Prints a help message and exits.
-i Disables inotify support.
-m This option allows you to specify a shell command to use for
sending Cron mail output instead of using sendmail(8) This com‐
mand must accept a fully formatted mail message (with headers)
on standard input and send it as a mail message to the recipi‐
ents specified in the mail headers. Specifying the string off
(i.e., crond -m off) will disable the sending of mail.
-n Tells the daemon to run in the foreground. This can be useful
when starting it out of init. With this option is needed to
change pam setting. /etc/pam.d/crond must not enable
-p Allows Cron to accept any user set crontables.
-P Don't set PATH. PATH is instead inherited from the environment.
-c This option enables clustering support, as described below.
-s This option will direct Cron to send the job output to the sys‐
tem log using syslog(3). This is useful if your system does not
have sendmail(8), installed or if mail is disabled.
-x This option allows you to set debug flags.
When the SIGHUP is received, the Cron daemon will close and reopen its
log file. This proves to be useful in scripts which rotate and age log
files. Naturally, this is not relevant if Cron was built to use sys‐
In this version of Cron it is possible to use a network-mounted shared
/var/spool/cron across a cluster of hosts and specify that only one of
the hosts should run the crontab jobs in this directory at any one
time. This is done by starting Cron with the -c option, and have the
/var/spool/cron/.cron.hostname file contain just one line, which repre‐
sents the hostname of whichever host in the cluster should run the
jobs. If this file does not exist, or the hostname in it does not
match that returned by gethostname(2), then all crontab files in this
directory are ignored. This has no effect on cron jobs specified in
the /etc/crontab file or on files in the /etc/cron.d directory. These
files are always run and considered host-specific.
Rather than editing /var/spool/cron/.cron.hostname directly, use the -n
option of crontab(1) to specify the host.
You should ensure that all hosts in a cluster, and the file server from
which they mount the shared crontab directory, have closely synchro‐
nised clocks, e.g., using ntpd(8), otherwise the results will be very
Using cluster sharing automatically disables inotify support, because
inotify cannot be relied on with network-mounted shared file systems.
All crontab files have to be regular files or symlinks to regular
files, they must not be executable or writable for anyone else but the
owner. This requirement can be overridden by using the -p option on
the crond command line. If inotify support is in use, changes in the
symlinked crontabs are not automatically noticed by the cron daemon.
The cron daemon must receive a SIGHUP signal to reload the crontabs.
This is a limitation of the inotify API.
The syslog output will be used instead of mail, when sendmail is not
SEE ALSOcrontab(1), crontab(5), inotify(7), pam(8)AUTHOR
Paul Vixie ⟨email@example.com⟩
Marcela Mašláňová ⟨firstname.lastname@example.org⟩
Colin Dean ⟨email@example.com⟩
cronie 2013-09-26 CRON(8)