if_bge man page on FreeBSD

Man page or keyword search:  
man Server   9747 pages
apropos Keyword Search (all sections)
Output format
FreeBSD logo
[printable version]

BGE(4)			 BSD Kernel Interfaces Manual			BGE(4)

NAME
     bge — Broadcom BCM57xx/BCM590x Gigabit/Fast Ethernet driver

SYNOPSIS
     To compile this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device miibus
	   device bge

     Alternatively, to load the driver as a module at boot time, place the
     following line in loader.conf(5):

	   if_bge_load="YES"

DESCRIPTION
     The bge driver provides support for various NICs based on the Broadcom
     BCM570x, 571x, 572x, 575x, 576x, 578x, 5776x and 5778x Gigabit Ethernet
     controller chips and the 590x and 5779x Fast Ethernet controller chips.

     All of these NICs are capable of 10, 100 and 1000Mbps speeds over CAT5
     copper cable, except for the SysKonnect SK-9D41 which supports only
     1000Mbps over multimode fiber.  The BCM570x builds upon the technology of
     the Alteon Tigon II.  It has two R4000 CPU cores and is PCI v2.2 and PCI-
     X v1.0 compliant.	It supports IP, TCP and UDP checksum offload for both
     receive and transmit, multiple RX and TX DMA rings for QoS applications,
     rules-based receive filtering, and VLAN tag stripping/insertion as well
     as a 256-bit multicast hash filter.  Additional features may be provided
     via value-add firmware updates.  The BCM570x supports TBI (ten bit inter‐
     face) and GMII transceivers, which means it can be used with either cop‐
     per or 1000baseX fiber applications.  Note however the device only sup‐
     ports a single speed in TBI mode.

     Most BCM5700-based cards also use the Broadcom BCM5401 or BCM5411
     10/100/1000 copper gigabit transceivers, which support autonegotiation of
     10, 100 and 1000Mbps modes in full or half duplex.

     The BCM5700, BCM5701, BCM5702, BCM5703, BCM5704 and BCM5717 also support
     jumbo frames, which can be configured via the interface MTU setting.
     Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility con‐
     figures the adapter to receive and transmit jumbo frames.	Using jumbo
     frames can greatly improve performance for certain tasks, such as file
     transfers and data streaming.

     The bge driver supports the following media types:

     autoselect	  Enable autoselection of the media type and options.  The
		  user can manually override the autoselected mode by adding
		  media options to rc.conf(5).

     10baseT/UTP  Set 10Mbps operation.	 The ifconfig(8) mediaopt option can
		  also be used to select either full-duplex or half-duplex
		  modes.

     100baseTX	  Set 100Mbps (Fast Ethernet) operation.  The ifconfig(8)
		  mediaopt option can also be used to select either
		  full-duplex or half-duplex modes.

     1000baseTX	  Set 1000baseTX operation over twisted pair.  Only
		  full-duplex mode is supported.

     1000baseSX	  Set 1000Mbps (Gigabit Ethernet) operation.  Both full-duplex
		  and half-duplex modes are supported.

     The bge driver supports the following media options:

     full-duplex  Force full duplex operation.

     half-duplex  Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).

HARDWARE
     The bge driver provides support for various NICs based on the Broadcom
     BCM570x family of Gigabit Ethernet controller chips, including the fol‐
     lowing:

     ·	 3Com 3c996-SX (1000baseSX)
     ·	 3Com 3c996-T (10/100/1000baseTX)
     ·	 Dell PowerEdge 1750 integrated BCM5704C NIC (10/100/1000baseTX)
     ·	 Dell PowerEdge 2550 integrated BCM5700 NIC (10/100/1000baseTX)
     ·	 Dell PowerEdge 2650 integrated BCM5703 NIC (10/100/1000baseTX)
     ·	 Dell PowerEdge R200 integrated BCM5750 NIC (10/100/1000baseTX)
     ·	 Dell PowerEdge R300 integrated BCM5722 NIC (10/100/1000baseTX)
     ·	 IBM x235 server integrated BCM5703x NIC (10/100/1000baseTX)
     ·	 HP Compaq dc7600 integrated BCM5752 NIC (10/100/1000baseTX)
     ·	 HP ProLiant NC7760 embedded Gigabit NIC (10/100/1000baseTX)
     ·	 HP ProLiant NC7770 PCI-X Gigabit NIC (10/100/1000baseTX)
     ·	 HP ProLiant NC7771 PCI-X Gigabit NIC (10/100/1000baseTX)
     ·	 HP ProLiant NC7781 embedded PCI-X Gigabit NIC (10/100/1000baseTX)
     ·	 Netgear GA302T (10/100/1000baseTX)
     ·	 SysKonnect SK-9D21 (10/100/1000baseTX)
     ·	 SysKonnect SK-9D41 (1000baseSX)

LOADER TUNABLES
     The following tunable can be set at the loader(8) prompt before booting
     the kernel, or stored in loader.conf(5).

     hw.bge.allow_asf
	     Allow the ASF feature for cooperating with IPMI.  Can cause sys‐
	     tem lockup problems on a small number of systems.	Disabled by
	     default.

SYSCTL VARIABLES
     The following variables are available as both sysctl(8) variables and
     loader(8) tunables:

     dev.bge.%d.forced_collapse
	     Allow collapsing multiple transmit buffers into a single buffer
	     to increase transmit performance with the cost of CPU cycles.
	     The default value is 0 to disable transmit buffer collapsing.

     dev.bge.%d.forced_udpcsum
	     Enable UDP transmit checksum offloading even if controller can
	     generate UDP datagrams with checksum value 0.  UDP datagrams with
	     checksum value 0 can confuse receiver host as it means sender did
	     not compute UDP checksum.	The default value is 0 which disables
	     UDP transmit checksum offloading.	The interface need to be
	     brought down and up again before a change takes effect.

DIAGNOSTICS
     bge%d: couldn't map memory	 A fatal initialization error has occurred.

     bge%d: couldn't map ports	A fatal initialization error has occurred.

     bge%d: couldn't map interrupt  A fatal initialization error has occurred.

     bge%d: no memory for softc struct!	 The driver failed to allocate memory
     for per-device instance information during initialization.

     bge%d: failed to enable memory mapping!  The driver failed to initialize
     PCI shared memory mapping.	 This might happen if the card is not in a
     bus-master slot.

     bge%d: no memory for jumbo buffers!  The driver failed to allocate memory
     for jumbo frames during initialization.

     bge%d: watchdog timeout  The device has stopped responding to the net‐
     work, or there is a problem with the network connection (cable).

SEE ALSO
     altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), polling(4),
     vlan(4), ifconfig(8)

HISTORY
     The bge device driver first appeared in FreeBSD 4.5.

AUTHORS
     The bge driver was written by Bill Paul ⟨wpaul@windriver.com⟩.

BSD			       November 23, 2010			   BSD
[top]

List of man pages available for FreeBSD

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
...................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net