in.rwhod(1M) System Administration Commands in.rwhod(1M)NAME
in.rwhod, rwhod - system status server
SYNOPSIS
/usr/sbin/in.rwhod [ -m [ttl]]
DESCRIPTIONin.rwhod is the server which maintains the database used by the rwho(1)
and ruptime(1) programs. Its operation is predicated on the ability to
broadcast or multicast messages on a network.
in.rwhod operates as both a producer and consumer of status informa‐
tion. As a producer of information it periodically queries the state of
the system and constructs status messages which are broadcast or multi‐
cast on a network. As a consumer of information, it listens for other
in.rwhod servers' status messages, validating them, then recording them
in a collection of files located in the directory /var/spool/rwho.
The rwho server transmits and receives messages at the port indicated
in the rwho service specification, see services(4). The messages sent
and received are defined in /usr/include/protocols/rwhod.h and are of
the form:
struct outmp {
char out_line[8]; /* tty name */
char out_name[8]; /* user id */
long out_time; /* time on */
};
struct whod {
char wd_vers;
char wd_type;
char wd_fill[2];
int wd_sendtime;
int wd_recvtime;
char wd_hostname[32];
int wd_loadav[3];
int wd_boottime;
struct whoent {
struct outmp we_utmp;
int we_idle;
} wd_we[1024 / sizeof (struct whoent)];
};
All fields are converted to network byte order prior to transmission.
The load averages are as calculated by the w(1) program, and represent
load averages over the 1, 5, and 15 minute intervals prior to a
server's transmission. The host name included is that returned by the
uname(2) system call. The array at the end of the message contains
information about the users who are logged in to the sending machine.
This information includes the contents of the utmpx(4) entry for each
non-idle terminal line and a value indicating the time since a charac‐
ter was last received on the terminal line.
Messages received by the rwho server are discarded unless they origi‐
nated at a rwho server's port. In addition, if the host's name, as
specified in the message, contains any unprintable ASCII characters,
the message is discarded.
Valid messages received by in.rwhod are placed in files named
whod.hostname in the directory /var/spool/rwho. These files contain
only the most recent message, in the format described above.
Status messages are generated approximately once every 3 minutes.
OPTIONS
The following options are supported:
-m [ ttl ] Use the rwho IP multicast address (224.0.1.3) when
transmitting. Receive announcements both on this multi‐
cast address and on the IP broadcast address. If ttl
is not specified in.rwhod multicasts on all interfaces
but with the IP TimeToLive set to 1 (that is, packets
are not forwarded by multicast routers.) If ttl is
specified in.rwhod only transmits packets on one
interface and setting the IP TimeToLive to the speci‐
fied ttl.
FILES
/var/spool/rwho/whod.* information about other machines
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
┌─────────────────────────────┬─────────────────────────────┐
│ ATTRIBUTE TYPE │ ATTRIBUTE VALUE │
├─────────────────────────────┼─────────────────────────────┤
│Availability │SUNWrcmds │
└─────────────────────────────┴─────────────────────────────┘
SEE ALSOruptime(1), rwho(1), w(1), uname(2), services(4), utmpx(4),
attributes(5)WARNINGS
This service can cause network performance problems when used by sev‐
eral hosts on the network. It is not run at most sites by default. If
used, include the -m multicast option.
NOTES
This service takes up progressively more network bandwidth as the num‐
ber of hosts on the local net increases. For large networks, the cost
becomes prohibitive.
in.rwhod should relay status information between networks. People often
interpret the server dying as a machine going down.
SunOS 5.10 8 Dec 2001 in.rwhod(1M)
