IP6TABLES(8) iptables 1.4.14 IP6TABLES(8)NAMEip6tables — IPv6 packet filter administration
SYNOPSISip6tables [-t table] {-A|-C|-D} chain rule-specification [options...]
ip6tables [-t table] -I chain [rulenum] rule-specification [options...]
ip6tables [-t table] -R chain rulenum rule-specification [options...]
ip6tables [-t table] -D chain rulenum [options...]
ip6tables [-t table] -S [chain [rulenum]]
ip6tables [-t table] {-F|-L|-Z} [chain [rulenum]] [options...]
ip6tables [-t table] -N chain
ip6tables [-t table] -X [chain]
ip6tables [-t table] -P chain target [options...]
ip6tables [-t table] -E old-chain-name new-chain-name
DESCRIPTION
Ip6tables is used to set up, maintain, and inspect the tables of IPv6
packet filter rules in the Linux kernel. Several different tables may
be defined. Each table contains a number of built-in chains and may
also contain user-defined chains.
Each chain is a list of rules which can match a set of packets. Each
rule specifies what to do with a packet that matches. This is called a
`target', which may be a jump to a user-defined chain in the same ta‐
ble.
TARGETS
A firewall rule specifies criteria for a packet and a target. If the
packet does not match, the next rule in the chain is the examined; if
it does match, then the next rule is specified by the value of the tar‐
get, which can be the name of a user-defined chain or one of the spe‐
cial values ACCEPT, DROP, QUEUE or RETURN.
ACCEPT means to let the packet through. DROP means to drop the packet
on the floor. QUEUE means to pass the packet to userspace. (How the
packet can be received by a userspace process differs by the particular
queue handler. 2.4.x and 2.6.x kernels up to 2.6.13 include the
ip_queue queue handler. Kernels 2.6.14 and later additionally include
the nfnetlink_queue queue handler. Packets with a target of QUEUE will
be sent to queue number '0' in this case. Please also see the NFQUEUE
target as described later in this man page.) RETURN means stop
traversing this chain and resume at the next rule in the previous
(calling) chain. If the end of a built-in chain is reached or a rule
in a built-in chain with target RETURN is matched, the target specified
by the chain policy determines the fate of the packet.
TABLES
There are currently three independent tables (which tables are present
at any time depends on the kernel configuration options and which mod‐
ules are present).
-t, --table table
This option specifies the packet matching table which the com‐
mand should operate on. If the kernel is configured with auto‐
matic module loading, an attempt will be made to load the appro‐
priate module for that table if it is not already there.
The tables are as follows:
filter:
This is the default table (if no -t option is passed). It
contains the built-in chains INPUT (for packets destined to
local sockets), FORWARD (for packets being routed through
the box), and OUTPUT (for locally-generated packets).
mangle:
This table is used for specialized packet alteration. Until
kernel 2.4.17 it had two built-in chains: PREROUTING (for
altering incoming packets before routing) and OUTPUT (for
altering locally-generated packets before routing). Since
kernel 2.4.18, three other built-in chains are also sup‐
ported: INPUT (for packets coming into the box itself), FOR‐
WARD (for altering packets being routed through the box),
and POSTROUTING (for altering packets as they are about to
go out).
raw:
This table is used mainly for configuring exemptions from
connection tracking in combination with the NOTRACK target.
It registers at the netfilter hooks with higher priority and
is thus called before ip_conntrack, or any other IP tables.
It provides the following built-in chains: PREROUTING (for
packets arriving via any network interface) OUTPUT (for
packets generated by local processes)
security:
This table is used for Mandatory Access Control (MAC) net‐
working rules, such as those enabled by the SECMARK and
CONNSECMARK targets. Mandatory Access Control is imple‐
mented by Linux Security Modules such as SELinux. The secu‐
rity table is called after the filter table, allowing any
Discretionary Access Control (DAC) rules in the filter table
to take effect before MAC rules. This table provides the
following built-in chains: INPUT (for packets coming into
the box itself), OUTPUT (for altering locally-generated
packets before routing), and FORWARD (for altering packets
being routed through the box).
OPTIONS
The options that are recognized by ip6tables can be divided into sev‐
eral different groups.
COMMANDS
These options specify the specific action to perform. Only one of them
can be specified on the command line unless otherwise specified below.
For all the long versions of the command and option names, you need to
use only enough letters to ensure that ip6tables can differentiate it
from all other options.
-A, --append chain rule-specification
Append one or more rules to the end of the selected chain. When
the source and/or destination names resolve to more than one
address, a rule will be added for each possible address combina‐
tion.
-C, --check chain rule-specification
Check whether a rule matching the specification does exist in
the selected chain. This command uses the same logic as -D to
find a matching entry, but does not alter the existing iptables
configuration and uses its exit code to indicate success or
failure.
-D, --delete chain rule-specification
-D, --delete chain rulenum
Delete one or more rules from the selected chain. There are two
versions of this command: the rule can be specified as a number
in the chain (starting at 1 for the first rule) or a rule to
match.
-I, --insert chain [rulenum] rule-specification
Insert one or more rules in the selected chain as the given rule
number. So, if the rule number is 1, the rule or rules are
inserted at the head of the chain. This is also the default if
no rule number is specified.
-R, --replace chain rulenum rule-specification
Replace a rule in the selected chain. If the source and/or des‐
tination names resolve to multiple addresses, the command will
fail. Rules are numbered starting at 1.
-L, --list [chain]
List all rules in the selected chain. If no chain is selected,
all chains are listed. Like every other ip6tables command, it
applies to the specified table (filter is the default).
Please note that it is often used with the -n option, in order
to avoid long reverse DNS lookups. It is legal to specify the
-Z (zero) option as well, in which case the chain(s) will be
atomically listed and zeroed. The exact output is affected by
the other arguments given. The exact rules are suppressed until
you use
ip6tables-L -v
-S, --list-rules [chain]
Print all rules in the selected chain. If no chain is selected,
all chains are printed like ip6tables-save. Like every other
ip6tables command, it applies to the specified table (filter is
the default).
-F, --flush [chain]
Flush the selected chain (all the chains in the table if none is
given). This is equivalent to deleting all the rules one by
one.
-Z, --zero [chain [rulenum]]
Zero the packet and byte counters in all chains, or only the
given chain, or only the given rule in a chain. It is legal to
specify the -L, --list (list) option as well, to see the coun‐
ters immediately before they are cleared. (See above.)
-N, --new-chain chain
Create a new user-defined chain by the given name. There must
be no target of that name already.
-X, --delete-chain [chain]
Delete the optional user-defined chain specified. There must be
no references to the chain. If there are, you must delete or
replace the referring rules before the chain can be deleted.
The chain must be empty, i.e. not contain any rules. If no
argument is given, it will attempt to delete every non-builtin
chain in the table.
-P, --policy chain target
Set the policy for the chain to the given target. See the sec‐
tion TARGETS for the legal targets. Only built-in (non-user-
defined) chains can have policies, and neither built-in nor
user-defined chains can be policy targets.
-E, --rename-chain old-chain new-chain
Rename the user specified chain to the user supplied name. This
is cosmetic, and has no effect on the structure of the table.
-A, --append chain rule-specification
Append one or more rules to the end of the selected chain. When
the source and/or destination names resolve to more than one
address, a rule will be added for each possible address combina‐
tion.
-h Help. Give a (currently very brief) description of the command
syntax.
PARAMETERS
The following parameters make up a rule specification (as used in the
add, delete, insert, replace and append commands).
[!] -p, --protocol protocol
The protocol of the rule or of the packet to check. The speci‐
fied protocol can be one of tcp, udp, udplite, icmpv6, esp, mh
or the special keyword "all", or it can be a numeric value, rep‐
resenting one of these protocols or a different one. A protocol
name from /etc/protocols is also allowed. But IPv6 extension
headers except esp are not allowed. esp and ipv6-nonext can be
used with Kernel version 2.6.11 or later. A "!" argument before
the protocol inverts the test. The number zero is equivalent to
all, which means that you cannot test the protocol field for the
value 0 directly. To match on a HBH header, even if it were the
last, you cannot use -p 0, but always need -m hbh. "all" will
match with all protocols and is taken as default when this
option is omitted.
[!] -s, --source address[/mask]
Source specification. Address can be either be a hostname, a
network IP address (with /mask), or a plain IP address. Names
will be resolved once only, before the rule is submitted to the
kernel. Please note that specifying any name to be resolved
with a remote query such as DNS is a really bad idea. (Resolv‐
ing network names is not supported at this time.) The mask is a
plain number, specifying the number of 1's at the left side of
the network mask. A "!" argument before the address specifica‐
tion inverts the sense of the address. The flag --src is an
alias for this option. Multiple addresses can be specified, but
this will expand to multiple rules (when adding with -A), or
will cause multiple rules to be deleted (with -D).
[!] -d, --destination address[/mask]
Destination specification. See the description of the -s
(source) flag for a detailed description of the syntax. The
flag --dst is an alias for this option.
-j, --jump target
This specifies the target of the rule; i.e., what to do if the
packet matches it. The target can be a user-defined chain
(other than the one this rule is in), one of the special builtin
targets which decide the fate of the packet immediately, or an
extension (see EXTENSIONS below). If this option is omitted in
a rule (and -g is not used), then matching the rule will have no
effect on the packet's fate, but the counters on the rule will
be incremented.
-g, --goto chain
This specifies that the processing should continue in a user
specified chain. Unlike the --jump option return will not con‐
tinue processing in this chain but instead in the chain that
called us via --jump.
[!] -i, --in-interface name
Name of an interface via which a packet was received (only for
packets entering the INPUT, FORWARD and PREROUTING chains).
When the "!" argument is used before the interface name, the
sense is inverted. If the interface name ends in a "+", then
any interface which begins with this name will match. If this
option is omitted, any interface name will match.
[!] -o, --out-interface name
Name of an interface via which a packet is going to be sent (for
packets entering the FORWARD, OUTPUT and POSTROUTING chains).
When the "!" argument is used before the interface name, the
sense is inverted. If the interface name ends in a "+", then
any interface which begins with this name will match. If this
option is omitted, any interface name will match.
-c, --set-counters packets bytes
This enables the administrator to initialize the packet and byte
counters of a rule (during INSERT, APPEND, REPLACE operations).
OTHER OPTIONS
The following additional options can be specified:
-v, --verbose
Verbose output. This option makes the list command show the
interface name, the rule options (if any), and the TOS masks.
The packet and byte counters are also listed, with the suffix
'K', 'M' or 'G' for 1000, 1,000,000 and 1,000,000,000 multipli‐
ers respectively (but see the -x flag to change this). For
appending, insertion, deletion and replacement, this causes
detailed information on the rule or rules to be printed. -v may
be specified multiple times to possibly emit more detailed debug
statements.
-n, --numeric
Numeric output. IP addresses and port numbers will be printed
in numeric format. By default, the program will try to display
them as host names, network names, or services (whenever appli‐
cable).
-x, --exact
Expand numbers. Display the exact value of the packet and byte
counters, instead of only the rounded number in K's (multiples
of 1000) M's (multiples of 1000K) or G's (multiples of 1000M).
This option is only relevant for the -L command.
--line-numbers
When listing rules, add line numbers to the beginning of each
rule, corresponding to that rule's position in the chain.
--modprobe=command
When adding or inserting rules into a chain, use command to load
any necessary modules (targets, match extensions, etc).
MATCH EXTENSIONSip6tables can use extended packet matching modules with the -m or
--match options, followed by the matching module name; after these,
various extra command line options become available, depending on the
specific module. You can specify multiple extended match modules in
one line, and you can use the -h or --help options after the module has
been specified to receive help specific to that module.
If the -p or --protocol was specified and if and only if an unknown
option is encountered, ip6tables will try load a match module of the
same name as the protocol, to try making the option available.
addrtype
This module matches packets based on their address type. Address types
are used within the kernel networking stack and categorize addresses
into various groups. The exact definition of that group depends on the
specific layer three protocol.
The following address types are possible:
UNSPEC an unspecified address (i.e. 0.0.0.0)
UNICAST
an unicast address
LOCAL a local address
BROADCAST
a broadcast address
ANYCAST
an anycast packet
MULTICAST
a multicast address
BLACKHOLE
a blackhole address
UNREACHABLE
an unreachable address
PROHIBIT
a prohibited address
THROW FIXME
NAT FIXME
XRESOLVE
[!] --src-type type
Matches if the source address is of given type
[!] --dst-type type
Matches if the destination address is of given type
--limit-iface-in
The address type checking can be limited to the interface the
packet is coming in. This option is only valid in the PREROUT‐
ING, INPUT and FORWARD chains. It cannot be specified with the
--limit-iface-out option.
--limit-iface-out
The address type checking can be limited to the interface the
packet is going out. This option is only valid in the POSTROUT‐
ING, OUTPUT and FORWARD chains. It cannot be specified with the
--limit-iface-in option.
ah
This module matches the parameters in Authentication header of IPsec
packets.
[!] --ahspi spi[:spi]
Matches SPI.
[!] --ahlen length
Total length of this header in octets.
--ahres
Matches if the reserved field is filled with zero.
cluster
Allows you to deploy gateway and back-end load-sharing clusters without
the need of load-balancers.
This match requires that all the nodes see the same packets. Thus, the
cluster match decides if this node has to handle a packet given the
following options:
--cluster-total-nodes num
Set number of total nodes in cluster.
[!] --cluster-local-node num
Set the local node number ID.
[!] --cluster-local-nodemask mask
Set the local node number ID mask. You can use this option
instead of --cluster-local-node.
--cluster-hash-seed value
Set seed value of the Jenkins hash.
Example:
iptables -A PREROUTING -t mangle -i eth1 -m cluster --clus‐
ter-total-nodes 2 --cluster-local-node 1 --cluster-hash-seed
0xdeadbeef -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth2 -m cluster --clus‐
ter-total-nodes 2 --cluster-local-node 1 --cluster-hash-seed
0xdeadbeef -j MARK --set-mark 0xffff
iptables -A PREROUTING -t mangle -i eth1 -m mark ! --mark 0xffff
-j DROP
iptables -A PREROUTING -t mangle -i eth2 -m mark ! --mark 0xffff
-j DROP
And the following commands to make all nodes see the same packets:
ip maddr add 01:00:5e:00:01:01 dev eth1
ip maddr add 01:00:5e:00:01:02 dev eth2
arptables -A OUTPUT -o eth1 --h-length 6 -j mangle --mangle-mac-
s 01:00:5e:00:01:01
arptables -A INPUT -i eth1 --h-length 6 --destination-mac
01:00:5e:00:01:01 -j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
arptables -A OUTPUT -o eth2 --h-length 6 -j mangle --man‐
gle-mac-s 01:00:5e:00:01:02
arptables -A INPUT -i eth2 --h-length 6 --destination-mac
01:00:5e:00:01:02 -j mangle --mangle-mac-d 00:zz:yy:xx:5a:27
In the case of TCP connections, pickup facility has to be disabled to
avoid marking TCP ACK packets coming in the reply direction as valid.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_loose
comment
Allows you to add comments (up to 256 characters) to any rule.
--comment comment
Example:
iptables -A INPUT -i eth1 -m comment --comment "my local LAN"
connbytes
Match by how many bytes or packets a connection (or one of the two
flows constituting the connection) has transferred so far, or by aver‐
age bytes per packet.
The counters are 64-bit and are thus not expected to overflow ;)
The primary use is to detect long-lived downloads and mark them to be
scheduled using a lower priority band in traffic control.
The transferred bytes per connection can also be viewed through `con‐
ntrack -L` and accessed via ctnetlink.
NOTE that for connections which have no accounting information, the
match will always return false. The "net.netfilter.nf_conntrack_acct"
sysctl flag controls whether new connections will be byte/packet
counted. Existing connection flows will not be gaining/losing a/the
accounting structure when be sysctl flag is flipped.
[!] --connbytes from[:to]
match packets from a connection whose packets/bytes/average
packet size is more than FROM and less than TO bytes/packets. if
TO is omitted only FROM check is done. "!" is used to match
packets not falling in the range.
--connbytes-dir {original|reply|both}
which packets to consider
--connbytes-mode {packets|bytes|avgpkt}
whether to check the amount of packets, number of bytes trans‐
ferred or the average size (in bytes) of all packets received so
far. Note that when "both" is used together with "avgpkt", and
data is going (mainly) only in one direction (for example HTTP),
the average packet size will be about half of the actual data
packets.
Example:
iptables .. -m connbytes --connbytes 10000:100000
--connbytes-dir both --connbytes-mode bytes ...
connlimit
Allows you to restrict the number of parallel connections to a server
per client IP address (or client address block).
--connlimit-upto n
Match if the number of existing connections is below or equal n.
--connlimit-above n
Match if the number of existing connections is above n.
--connlimit-mask prefix_length
Group hosts using the prefix length. For IPv4, this must be a
number between (including) 0 and 32. For IPv6, between 0 and
128. If not specified, the maximum prefix length for the appli‐
cable protocol is used.
--connlimit-saddr
Apply the limit onto the source group. This is the default if
--connlimit-daddr is not specified.
--connlimit-daddr
Apply the limit onto the destination group.
Examples:
# allow 2 telnet connections per client host
iptables -A INPUT -p tcp --syn--dport 23 -m connlimit
--connlimit-above 2 -j REJECT
# you can also match the other way around:
iptables -A INPUT -p tcp --syn--dport 23 -m connlimit
--connlimit-upto 2 -j ACCEPT
# limit the number of parallel HTTP requests to 16 per class C sized
source network (24 bit netmask)
iptables -p tcp --syn --dport 80 -m connlimit --connlimit-above
16 --connlimit-mask 24 -j REJECT
# limit the number of parallel HTTP requests to 16 for the link local
network
(ipv6) ip6tables-p tcp --syn--dport 80 -s fe80::/64 -m
connlimit --connlimit-above 16 --connlimit-mask 64 -j REJECT
# Limit the number of connections to a particular host:
ip6tables-p tcp --syn --dport 49152:65535 -d 2001:db8::1 -m
connlimit --connlimit-above 100 -j REJECT
connmark
This module matches the netfilter mark field associated with a connec‐
tion (which can be set using the CONNMARK target below).
[!] --mark value[/mask]
Matches packets in connections with the given mark value (if a
mask is specified, this is logically ANDed with the mark before
the comparison).
conntrack
This module, when combined with connection tracking, allows access to
the connection tracking state for this packet/connection.
[!] --ctstate statelist
statelist is a comma separated list of the connection states to
match. Possible states are listed below.
[!] --ctproto l4proto
Layer-4 protocol to match (by number or name)
[!] --ctorigsrc address[/mask]
[!] --ctorigdst address[/mask]
[!] --ctreplsrc address[/mask]
[!] --ctrepldst address[/mask]
Match against original/reply source/destination address
[!] --ctorigsrcport port[:port]
[!] --ctorigdstport port[:port]
[!] --ctreplsrcport port[:port]
[!] --ctrepldstport port[:port]
Match against original/reply source/destination port
(TCP/UDP/etc.) or GRE key. Matching against port ranges is only
supported in kernel versions above 2.6.38.
[!] --ctstatus statelist
statuslist is a comma separated list of the connection statuses
to match. Possible statuses are listed below.
[!] --ctexpire time[:time]
Match remaining lifetime in seconds against given value or range
of values (inclusive)
--ctdir {ORIGINAL|REPLY}
Match packets that are flowing in the specified direction. If
this flag is not specified at all, matches packets in both
directions.
States for --ctstate:
INVALID
meaning that the packet is associated with no known connection
NEW meaning that the packet has started a new connection, or other‐
wise associated with a connection which has not seen packets in
both directions, and
ESTABLISHED
meaning that the packet is associated with a connection which
has seen packets in both directions,
RELATED
meaning that the packet is starting a new connection, but is
associated with an existing connection, such as an FTP data
transfer, or an ICMP error.
UNTRACKED
meaning that the packet is not tracked at all, which happens if
you use the NOTRACK target in raw table.
SNAT A virtual state, matching if the original source address differs
from the reply destination.
DNAT A virtual state, matching if the original destination differs
from the reply source.
Statuses for --ctstatus:
NONE None of the below.
EXPECTED
This is an expected connection (i.e. a conntrack helper set it
up)
SEEN_REPLY
Conntrack has seen packets in both directions.
ASSURED
Conntrack entry should never be early-expired.
CONFIRMED
Connection is confirmed: originating packet has left box.
cpu
[!] --cpu number
Match cpu handling this packet. cpus are numbered from 0 to
NR_CPUS-1 Can be used in combination with RPS (Remote Packet
Steering) or multiqueue NICs to spread network traffic on dif‐
ferent queues.
Example:
iptables -t nat -A PREROUTING -p tcp --dport 80 -m cpu --cpu 0 -j REDI‐
RECT --to-port 8080
iptables -t nat -A PREROUTING -p tcp --dport 80 -m cpu --cpu 1 -j REDI‐
RECT --to-port 8081
Available since Linux 2.6.36.
dccp
[!] --source-port,--sport port[:port]
[!] --destination-port,--dport port[:port]
[!] --dccp-types mask
Match when the DCCP packet type is one of 'mask'. 'mask' is a
comma-separated list of packet types. Packet types are: REQUEST
RESPONSE DATA ACK DATAACK CLOSEREQ CLOSE RESET SYNC SYNCACK
INVALID.
[!] --dccp-option number
Match if DCCP option set.
dscp
This module matches the 6 bit DSCP field within the TOS field in the IP
header. DSCP has superseded TOS within the IETF.
[!] --dscp value
Match against a numeric (decimal or hex) value [0-63].
[!] --dscp-class class
Match the DiffServ class. This value may be any of the BE, EF,
AFxx or CSx classes. It will then be converted into its accord‐
ing numeric value.
dst
This module matches the parameters in Destination Options header
[!] --dst-len length
Total length of this header in octets.
--dst-opts type[:length][,type[:length]...]
numeric type of option and the length of the option data in
octets.
ecn
This allows you to match the ECN bits of the IPv4/IPv6 and TCP header.
ECN is the Explicit Congestion Notification mechanism as specified in
RFC3168
[!] --ecn-tcp-cwr
This matches if the TCP ECN CWR (Congestion Window Received) bit
is set.
[!] --ecn-tcp-ece
This matches if the TCP ECN ECE (ECN Echo) bit is set.
[!] --ecn-ip-ect num
This matches a particular IPv4/IPv6 ECT (ECN-Capable Transport).
You have to specify a number between `0' and `3'.
esp
This module matches the SPIs in ESP header of IPsec packets.
[!] --espspi spi[:spi]
eui64
This module matches the EUI-64 part of a stateless autoconfigured IPv6
address. It compares the EUI-64 derived from the source MAC address in
Ethernet frame with the lower 64 bits of the IPv6 source address. But
"Universal/Local" bit is not compared. This module doesn't match other
link layer frame, and is only valid in the PREROUTING, INPUT and FOR‐
WARD chains.
frag
This module matches the parameters in Fragment header.
[!] --fragid id[:id]
Matches the given Identification or range of it.
[!] --fraglen length
This option cannot be used with kernel version 2.6.10 or later.
The length of Fragment header is static and this option doesn't
make sense.
--fragres
Matches if the reserved fields are filled with zero.
--fragfirst
Matches on the first fragment.
--fragmore
Matches if there are more fragments.
--fraglast
Matches if this is the last fragment.
hashlimit
hashlimit uses hash buckets to express a rate limiting match (like the
limit match) for a group of connections using a single iptables rule.
Grouping can be done per-hostgroup (source and/or destination address)
and/or per-port. It gives you the ability to express "N packets per
time quantum per group" (see below for some examples).
A hash limit option (--hashlimit-upto, --hashlimit-above) and --hash‐
limit-name are required.
--hashlimit-upto amount[/second|/minute|/hour|/day]
Match if the rate is below or equal to amount/quantum. It is
specified as a number, with an optional time quantum suffix; the
default is 3/hour.
--hashlimit-above amount[/second|/minute|/hour|/day]
Match if the rate is above amount/quantum.
--hashlimit-burst amount
Maximum initial number of packets to match: this number gets
recharged by one every time the limit specified above is not
reached, up to this number; the default is 5.
--hashlimit-mode {srcip|srcport|dstip|dstport},...
A comma-separated list of objects to take into consideration. If
no --hashlimit-mode option is given, hashlimit acts like limit,
but at the expensive of doing the hash housekeeping.
--hashlimit-srcmask prefix
When --hashlimit-mode srcip is used, all source addresses
encountered will be grouped according to the given prefix length
and the so-created subnet will be subject to hashlimit. prefix
must be between (inclusive) 0 and 32. Note that --hashlimit-src‐
mask 0 is basically doing the same thing as not specifying srcip
for --hashlimit-mode, but is technically more expensive.
--hashlimit-dstmask prefix
Like --hashlimit-srcmask, but for destination addresses.
--hashlimit-name foo
The name for the /proc/net/ipt_hashlimit/foo entry.
--hashlimit-htable-size buckets
The number of buckets of the hash table
--hashlimit-htable-max entries
Maximum entries in the hash.
--hashlimit-htable-expire msec
After how many milliseconds do hash entries expire.
--hashlimit-htable-gcinterval msec
How many milliseconds between garbage collection intervals.
Examples:
matching on source host
"1000 packets per second for every host in 192.168.0.0/16" => -s
192.168.0.0/16 --hashlimit-mode srcip --hashlimit-upto 1000/sec
matching on source port
"100 packets per second for every service of 192.168.1.1" => -s
192.168.1.1 --hashlimit-mode srcport --hashlimit-upto 100/sec
matching on subnet
"10000 packets per minute for every /28 subnet (groups of 8
addresses) in 10.0.0.0/8" => -s 10.0.0.8 --hashlimit-mask 28
--hashlimit-upto 10000/min
hbh
This module matches the parameters in Hop-by-Hop Options header
[!] --hbh-len length
Total length of this header in octets.
--hbh-opts type[:length][,type[:length]...]
numeric type of option and the length of the option data in
octets.
helper
This module matches packets related to a specific conntrack-helper.
[!] --helper string
Matches packets related to the specified conntrack-helper.
string can be "ftp" for packets related to a ftp-session on
default port. For other ports append -portnr to the value, ie.
"ftp-2121".
Same rules apply for other conntrack-helpers.
hl
This module matches the Hop Limit field in the IPv6 header.
[!] --hl-eq value
Matches if Hop Limit equals value.
--hl-lt value
Matches if Hop Limit is less than value.
--hl-gt value
Matches if Hop Limit is greater than value.
icmp6
This extension can be used if `--protocol ipv6-icmp' or `--protocol
icmpv6' is specified. It provides the following option:
[!] --icmpv6-type type[/code]|typename
This allows specification of the ICMPv6 type, which can be a
numeric ICMPv6 type, type and code, or one of the ICMPv6 type
names shown by the command
ip6tables-p ipv6-icmp -h
iprange
This matches on a given arbitrary range of IP addresses.
[!] --src-range from[-to]
Match source IP in the specified range.
[!] --dst-range from[-to]
Match destination IP in the specified range.
ipv6header
This module matches IPv6 extension headers and/or upper layer header.
--soft Matches if the packet includes any of the headers specified with
--header.
[!] --header header[,header...]
Matches the packet which EXACTLY includes all specified headers.
The headers encapsulated with ESP header are out of scope. Pos‐
sible header types can be:
hop|hop-by-hop
Hop-by-Hop Options header
dst Destination Options header
route Routing header
frag Fragment header
auth Authentication header
esp Encapsulating Security Payload header
none No Next header which matches 59 in the 'Next Header field' of
IPv6 header or any IPv6 extension headers
proto which matches any upper layer protocol header. A protocol name
from /etc/protocols and numeric value also allowed. The number
255 is equivalent to proto.
ipvs
Match IPVS connection properties.
[!] --ipvs
packet belongs to an IPVS connection
Any of the following options implies --ipvs (even negated)
[!] --vproto protocol
VIP protocol to match; by number or name, e.g. "tcp"
[!] --vaddr address[/mask]
VIP address to match
[!] --vport port
VIP port to match; by number or name, e.g. "http"
--vdir {ORIGINAL|REPLY}
flow direction of packet
[!] --vmethod {GATE|IPIP|MASQ}
IPVS forwarding method used
[!] --vportctl port
VIP port of the controlling connection to match, e.g. 21 for FTP
length
This module matches the length of the layer-3 payload (e.g. layer-4
packet) of a packet against a specific value or range of values.
[!] --length length[:length]
limit
This module matches at a limited rate using a token bucket filter. A
rule using this extension will match until this limit is reached. It
can be used in combination with the LOG target to give limited logging,
for example.
xt_limit has no negation support - you will have to use -m hashlimit !
--hashlimit rate in this case whilst omitting --hashlimit-mode.
--limit rate[/second|/minute|/hour|/day]
Maximum average matching rate: specified as a number, with an
optional `/second', `/minute', `/hour', or `/day' suffix; the
default is 3/hour.
--limit-burst number
Maximum initial number of packets to match: this number gets
recharged by one every time the limit specified above is not
reached, up to this number; the default is 5.
mac
[!] --mac-source address
Match source MAC address. It must be of the form
XX:XX:XX:XX:XX:XX. Note that this only makes sense for packets
coming from an Ethernet device and entering the PREROUTING, FOR‐
WARD or INPUT chains.
mark
This module matches the netfilter mark field associated with a packet
(which can be set using the MARK target below).
[!] --mark value[/mask]
Matches packets with the given unsigned mark value (if a mask is
specified, this is logically ANDed with the mask before the com‐
parison).
mh
This extension is loaded if `--protocol ipv6-mh' or `--protocol mh' is
specified. It provides the following option:
[!] --mh-type type[:type]
This allows specification of the Mobility Header(MH) type, which
can be a numeric MH type, type or one of the MH type names shown
by the command
ip6tables-p ipv6-mh -h
multiport
This module matches a set of source or destination ports. Up to 15
ports can be specified. A port range (port:port) counts as two ports.
It can only be used in conjunction with -p tcp or -p udp.
[!] --source-ports,--sports port[,port|,port:port]...
Match if the source port is one of the given ports. The flag
--sports is a convenient alias for this option. Multiple ports
or port ranges are separated using a comma, and a port range is
specified using a colon. 53,1024:65535 would therefore match
ports 53 and all from 1024 through 65535.
[!] --destination-ports,--dports port[,port|,port:port]...
Match if the destination port is one of the given ports. The
flag --dports is a convenient alias for this option.
[!] --ports port[,port|,port:port]...
Match if either the source or destination ports are equal to one
of the given ports.
nfacct
The nfacct match provides the extended accounting infrastructure for
iptables. You have to use this match together with the standalone
user-space utility nfacct(8)
The only option available for this match is the following:
--nfacct-name name
This allows you to specify the existing object name that will be
use for accounting the traffic that this rule-set is matching.
To use this extension, you have to create an accounting object:
nfacct add http-traffic
Then, you have to attach it to the accounting object via iptables:
iptables -I INPUT -p tcp --sport 80 -m nfacct --nfacct-name
http-traffic
iptables -I OUTPUT -p tcp --dport 80 -m nfacct --nfacct-name
http-traffic
Then, you can check for the amount of traffic that the rules match:
nfacct get http-traffic
{ pkts = 00000000000000000156, bytes = 00000000000000151786 } =
http-traffic;
You can obtain nfacct(8) from http://www.netfilter.org or, alterna‐
tively, from the git.netfilter.org repository.
owner
This module attempts to match various characteristics of the packet
creator, for locally generated packets. This match is only valid in the
OUTPUT and POSTROUTING chains. Forwarded packets do not have any socket
associated with them. Packets from kernel threads do have a socket, but
usually no owner.
[!] --uid-owner username
[!] --uid-owner userid[-userid]
Matches if the packet socket's file structure (if it has one) is
owned by the given user. You may also specify a numerical UID,
or an UID range.
[!] --gid-owner groupname
[!] --gid-owner groupid[-groupid]
Matches if the packet socket's file structure is owned by the
given group. You may also specify a numerical GID, or a GID
range.
[!] --socket-exists
Matches if the packet is associated with a socket.
physdev
This module matches on the bridge port input and output devices
enslaved to a bridge device. This module is a part of the infrastruc‐
ture that enables a transparent bridging IP firewall and is only useful
for kernel versions above version 2.5.44.
[!] --physdev-in name
Name of a bridge port via which a packet is received (only for
packets entering the INPUT, FORWARD and PREROUTING chains). If
the interface name ends in a "+", then any interface which
begins with this name will match. If the packet didn't arrive
through a bridge device, this packet won't match this option,
unless '!' is used.
[!] --physdev-out name
Name of a bridge port via which a packet is going to be sent
(for packets entering the FORWARD, OUTPUT and POSTROUTING
chains). If the interface name ends in a "+", then any inter‐
face which begins with this name will match. Note that in the
nat and mangle OUTPUT chains one cannot match on the bridge out‐
put port, however one can in the filter OUTPUT chain. If the
packet won't leave by a bridge device or if it is yet unknown
what the output device will be, then the packet won't match this
option, unless '!' is used.
[!] --physdev-is-in
Matches if the packet has entered through a bridge interface.
[!] --physdev-is-out
Matches if the packet will leave through a bridge interface.
[!] --physdev-is-bridged
Matches if the packet is being bridged and therefore is not
being routed. This is only useful in the FORWARD and POSTROUT‐
ING chains.
pkttype
This module matches the link-layer packet type.
[!] --pkt-type {unicast|broadcast|multicast}
policy
This modules matches the policy used by IPsec for handling a packet.
--dir {in|out}
Used to select whether to match the policy used for decapsula‐
tion or the policy that will be used for encapsulation. in is
valid in the PREROUTING, INPUT and FORWARD chains, out is valid
in the POSTROUTING, OUTPUT and FORWARD chains.
--pol {none|ipsec}
Matches if the packet is subject to IPsec processing. --pol none
cannot be combined with --strict.
--strict
Selects whether to match the exact policy or match if any rule
of the policy matches the given policy.
For each policy element that is to be described, one can use one or
more of the following options. When --strict is in effect, at least one
must be used per element.
[!] --reqid id
Matches the reqid of the policy rule. The reqid can be specified
with setkey(8) using unique:id as level.
[!] --spi spi
Matches the SPI of the SA.
[!] --proto {ah|esp|ipcomp}
Matches the encapsulation protocol.
[!] --mode {tunnel|transport}
Matches the encapsulation mode.
[!] --tunnel-src addr[/mask]
Matches the source end-point address of a tunnel mode SA. Only
valid with --mode tunnel.
[!] --tunnel-dst addr[/mask]
Matches the destination end-point address of a tunnel mode SA.
Only valid with --mode tunnel.
--next Start the next element in the policy specification. Can only be
used with --strict.
quota
Implements network quotas by decrementing a byte counter with each
packet. The condition matches until the byte counter reaches zero.
Behavior is reversed with negation (i.e. the condition does not match
until the byte counter reaches zero).
[!] --quota bytes
The quota in bytes.
rateest
The rate estimator can match on estimated rates as collected by the
RATEEST target. It supports matching on absolute bps/pps values, com‐
paring two rate estimators and matching on the difference between two
rate estimators.
For a better understanding of the available options, these are all pos‐
sible combinations:
· rateest operator rateest-bps
· rateest operator rateest-pps
· (rateest minus rateest-bps1) operator rateest-bps2
· (rateest minus rateest-pps1) operator rateest-pps2
· rateest1 operator rateest2 rateest-bps(without rate!)
· rateest1 operator rateest2 rateest-pps(without rate!)
· (rateest1 minus rateest-bps1) operator (rateest2 minus rateest-
bps2)
· (rateest1 minus rateest-pps1) operator (rateest2 minus rateest-
pps2)
--rateest-delta
For each estimator (either absolute or relative mode), calculate
the difference between the estimator-determined flow rate and the
static value chosen with the BPS/PPS options. If the flow rate is
higher than the specified BPS/PPS, 0 will be used instead of a neg‐
ative value. In other words, "max(0, rateest#_rate - rateest#_bps)"
is used.
[!] --rateest-lt
Match if rate is less than given rate/estimator.
[!] --rateest-gt
Match if rate is greater than given rate/estimator.
[!] --rateest-eq
Match if rate is equal to given rate/estimator.
In the so-called "absolute mode", only one rate estimator is used and
compared against a static value, while in "relative mode", two rate
estimators are compared against another.
--rateest name
Name of the one rate estimator for absolute mode.
--rateest1 name
--rateest2 name
The names of the two rate estimators for relative mode.
--rateest-bps [value]
--rateest-pps [value]
--rateest-bps1 [value]
--rateest-bps2 [value]
--rateest-pps1 [value]
--rateest-pps2 [value]
Compare the estimator(s) by bytes or packets per second, and
compare against the chosen value. See the above bullet list for
which option is to be used in which case. A unit suffix may be
used - available ones are: bit, [kmgt]bit, [KMGT]ibit, Bps,
[KMGT]Bps, [KMGT]iBps.
Example: This is what can be used to route outgoing data connections
from an FTP server over two lines based on the available bandwidth at
the time the data connection was started:
# Estimate outgoing rates
iptables -t mangle -A POSTROUTING -o eth0 -j RATEEST --rateest-name
eth0 --rateest-interval 250ms --rateest-ewma 0.5s
iptables -t mangle -A POSTROUTING -o ppp0 -j RATEEST --rateest-name
ppp0 --rateest-interval 250ms --rateest-ewma 0.5s
# Mark based on available bandwidth
iptables -t mangle -A balance -m conntrack --ctstate NEW -m helper
--helper ftp -m rateest --rateest-delta --rateest1 eth0 --rateest-bps1
2.5mbit --rateest-gt --rateest2 ppp0 --rateest-bps2 2mbit -j CONNMARK
--set-mark 1
iptables -t mangle -A balance -m conntrack --ctstate NEW -m helper
--helper ftp -m rateest --rateest-delta --rateest1 ppp0 --rateest-bps1
2mbit --rateest-gt--rateest2 eth0 --rateest-bps2 2.5mbit -j CONNMARK
--set-mark 2
iptables -t mangle -A balance -j CONNMARK --restore-mark
recent
Allows you to dynamically create a list of IP addresses and then match
against that list in a few different ways.
For example, you can create a "badguy" list out of people attempting to
connect to port 139 on your firewall and then DROP all future packets
from them without considering them.
--set, --rcheck, --update and --remove are mutually exclusive.
--name name
Specify the list to use for the commands. If no name is given
then DEFAULT will be used.
[!] --set
This will add the source address of the packet to the list. If
the source address is already in the list, this will update the
existing entry. This will always return success (or failure if !
is passed in).
--rsource
Match/save the source address of each packet in the recent list
table. This is the default.
--rdest
Match/save the destination address of each packet in the recent
list table.
[!] --rcheck
Check if the source address of the packet is currently in the
list.
[!] --update
Like --rcheck, except it will update the "last seen" timestamp
if it matches.
[!] --remove
Check if the source address of the packet is currently in the
list and if so that address will be removed from the list and
the rule will return true. If the address is not found, false is
returned.
--seconds seconds
This option must be used in conjunction with one of --rcheck or
--update. When used, this will narrow the match to only happen
when the address is in the list and was seen within the last
given number of seconds.
--reap This option can only be used in conjunction with --seconds.
When used, this will cause entries older than the last given
number of seconds to be purged.
--hitcount hits
This option must be used in conjunction with one of --rcheck or
--update. When used, this will narrow the match to only happen
when the address is in the list and packets had been received
greater than or equal to the given value. This option may be
used along with --seconds to create an even narrower match
requiring a certain number of hits within a specific time frame.
The maximum value for the hitcount parameter is given by the
"ip_pkt_list_tot" parameter of the xt_recent kernel module.
Exceeding this value on the command line will cause the rule to
be rejected.
--rttl This option may only be used in conjunction with one of --rcheck
or --update. When used, this will narrow the match to only hap‐
pen when the address is in the list and the TTL of the current
packet matches that of the packet which hit the --set rule. This
may be useful if you have problems with people faking their
source address in order to DoS you via this module by disallow‐
ing others access to your site by sending bogus packets to you.
Examples:
iptables -A FORWARD -m recent --name badguy --rcheck--seconds
60 -j DROP
iptables -A FORWARD -p tcp -i eth0 --dport 139 -m recent --name
badguy --set -j DROP
Steve's ipt_recent website (http://snowman.net/projects/ipt_recent/)
also has some examples of usage.
/proc/net/xt_recent/* are the current lists of addresses and informa‐
tion about each entry of each list.
Each file in /proc/net/xt_recent/ can be read from to see the current
list or written two using the following commands to modify the list:
echo +addr >/proc/net/xt_recent/DEFAULT
to add addr to the DEFAULT list
echo -addr >/proc/net/xt_recent/DEFAULT
to remove addr from the DEFAULT list
echo / >/proc/net/xt_recent/DEFAULT
to flush the DEFAULT list (remove all entries).
The module itself accepts parameters, defaults shown:
ip_list_tot=100
Number of addresses remembered per table.
ip_pkt_list_tot=20
Number of packets per address remembered.
ip_list_hash_size=0
Hash table size. 0 means to calculate it based on ip_list_tot,
default: 512.
ip_list_perms=0644
Permissions for /proc/net/xt_recent/* files.
ip_list_uid=0
Numerical UID for ownership of /proc/net/xt_recent/* files.
ip_list_gid=0
Numerical GID for ownership of /proc/net/xt_recent/* files.
rpfilter
Performs a reverse path filter test on a packet. If a reply to the
packet would be sent via the same interface that the packet arrived on,
the packet will match. Note that, unlike the in-kernel rp_filter,
packets protected by IPSec are not treated specially. Combine this
match with the policy match if you want this. Also, packets arriving
via the loopback interface are always permitted. This match can only
be used in the PREROUTING chain of the raw or mangle table.
--loose
Used to specifiy that the reverse path filter test should match
even if the selected output device is not the expected one.
--validmark
Also use the packets' nfmark value when performing the reverse
path route lookup.
--accept-local
This will permit packets arriving from the network with a source
address that is also assigned to the local machine. --invert
This will invert the sense of the match. Instead of matching
packets that passed the reverse path filter test, match those
that have failed it.
Example to log and drop packets failing the reverse path filter test:
iptables -t raw -N RPFILTER
iptables -t raw -A RPFILTER -m rpfilter -j RETURN
iptables -t raw -A RPFILTER -m limit --limit 10/minute -j NFLOG
--nflog-prefix "rpfilter drop"
iptables -t raw -A RPFILTER -j DROP
iptables -t raw -A PREROUTING -j RPFILTER
Example to drop failed packets, without logging:
iptables -t raw -A RPFILTER -m rpfilter --invert -j DROP
rt
Match on IPv6 routing header
[!] --rt-type type
Match the type (numeric).
[!] --rt-segsleft num[:num]
Match the `segments left' field (range).
[!] --rt-len length
Match the length of this header.
--rt-0-res
Match the reserved field, too (type=0)
--rt-0-addrs addr[,addr...]
Match type=0 addresses (list).
--rt-0-not-strict
List of type=0 addresses is not a strict list.
sctp
[!] --source-port,--sport port[:port]
[!] --destination-port,--dport port[:port]
[!] --chunk-types {all|any|only} chunktype[:flags] [...]
The flag letter in upper case indicates that the flag is to
match if set, in the lower case indicates to match if unset.
Chunk types: DATA INIT INIT_ACK SACK HEARTBEAT HEARTBEAT_ACK
ABORT SHUTDOWN SHUTDOWN_ACK ERROR COOKIE_ECHO COOKIE_ACK
ECN_ECNE ECN_CWR SHUTDOWN_COMPLETE ASCONF ASCONF_ACK FORWARD_TSN
chunk type available flags
DATA I U B E i u b e
ABORT T t
SHUTDOWN_COMPLETE T t
(lowercase means flag should be "off", uppercase means "on")
Examples:
iptables -A INPUT -p sctp --dport 80 -j DROP
iptables -A INPUT -p sctp --chunk-types any DATA,INIT -j DROP
iptables -A INPUT -p sctp --chunk-types any DATA:Be -j ACCEPT
set
This module matches IP sets which can be defined by ipset(8).
[!] --match-set setname flag[,flag]...
where flags are the comma separated list of src and/or dst spec‐
ifications and there can be no more than six of them. Hence the
command
iptables -A FORWARD -m set --match-set test src,dst
will match packets, for which (if the set type is ipportmap) the
source address and destination port pair can be found in the
specified set. If the set type of the specified set is single
dimension (for example ipmap), then the command will match pack‐
ets for which the source address can be found in the specified
set.
The option --match-set can be replaced by --set if that does not clash
with an option of other extensions.
Use of -m set requires that ipset kernel support is provided, which,
for standard kernels, is the case since Linux 2.6.39.
socket
This matches if an open socket can be found by doing a socket lookup on
the packet.
--transparent
Ignore non-transparent sockets.
state
This module, when combined with connection tracking, allows access to
the connection tracking state for this packet.
[!] --state state
Where state is a comma separated list of the connection states
to match. Possible states are INVALID meaning that the packet
could not be identified for some reason which includes running
out of memory and ICMP errors which don't correspond to any
known connection, ESTABLISHED meaning that the packet is associ‐
ated with a connection which has seen packets in both direc‐
tions, NEW meaning that the packet has started a new connection,
or otherwise associated with a connection which has not seen
packets in both directions, and RELATED meaning that the packet
is starting a new connection, but is associated with an existing
connection, such as an FTP data transfer, or an ICMP error.
UNTRACKED meaning that the packet is not tracked at all, which
happens if you use the NOTRACK target in raw table.
statistic
This module matches packets based on some statistic condition. It sup‐
ports two distinct modes settable with the --mode option.
Supported options:
--mode mode
Set the matching mode of the matching rule, supported modes are
random and nth.
[!] --probability p
Set the probability for a packet to be randomly matched. It only
works with the random mode. p must be within 0.0 and 1.0. The
supported granularity is in 1/2147483648th increments.
[!] --every n
Match one packet every nth packet. It works only with the nth
mode (see also the --packet option).
--packet p
Set the initial counter value (0 <= p <= n-1, default 0) for the
nth mode.
string
This modules matches a given string by using some pattern matching
strategy. It requires a linux kernel >= 2.6.14.
--algo {bm|kmp}
Select the pattern matching strategy. (bm = Boyer-Moore, kmp =
Knuth-Pratt-Morris)
--from offset
Set the offset from which it starts looking for any matching. If
not passed, default is 0.
--to offset
Set the offset up to which should be scanned. That is, byte off‐
set-1 (counting from 0) is the last one that is scanned. If not
passed, default is the packet size.
[!] --string pattern
Matches the given pattern.
[!] --hex-string pattern
Matches the given pattern in hex notation.
tcp
These extensions can be used if `--protocol tcp' is specified. It pro‐
vides the following options:
[!] --source-port,--sport port[:port]
Source port or port range specification. This can either be a
service name or a port number. An inclusive range can also be
specified, using the format first:last. If the first port is
omitted, "0" is assumed; if the last is omitted, "65535" is
assumed. If the first port is greater than the second one they
will be swapped. The flag --sport is a convenient alias for
this option.
[!] --destination-port,--dport port[:port]
Destination port or port range specification. The flag --dport
is a convenient alias for this option.
[!] --tcp-flags mask comp
Match when the TCP flags are as specified. The first argument
mask is the flags which we should examine, written as a comma-
separated list, and the second argument comp is a comma-sepa‐
rated list of flags which must be set. Flags are: SYN ACK FIN
RST URG PSH ALL NONE. Hence the command
iptables -A FORWARD -p tcp --tcp-flags SYN,ACK,FIN,RST SYN
will only match packets with the SYN flag set, and the ACK, FIN
and RST flags unset.
[!] --syn
Only match TCP packets with the SYN bit set and the ACK,RST and
FIN bits cleared. Such packets are used to request TCP connec‐
tion initiation; for example, blocking such packets coming in an
interface will prevent incoming TCP connections, but outgoing
TCP connections will be unaffected. It is equivalent to
--tcp-flags SYN,RST,ACK,FIN SYN. If the "!" flag precedes the
"--syn", the sense of the option is inverted.
[!] --tcp-option number
Match if TCP option set.
tcpmss
This matches the TCP MSS (maximum segment size) field of the TCP
header. You can only use this on TCP SYN or SYN/ACK packets, since the
MSS is only negotiated during the TCP handshake at connection startup
time.
[!] --mss value[:value]
Match a given TCP MSS value or range.
time
This matches if the packet arrival time/date is within a given range.
All options are optional, but are ANDed when specified. All times are
interpreted as UTC by default.
--datestart YYYY[-MM[-DD[Thh[:mm[:ss]]]]]
--datestop YYYY[-MM[-DD[Thh[:mm[:ss]]]]]
Only match during the given time, which must be in ISO 8601 "T"
notation. The possible time range is 1970-01-01T00:00:00 to
2038-01-19T04:17:07.
If --datestart or --datestop are not specified, it will default
to 1970-01-01 and 2038-01-19, respectively.
--timestart hh:mm[:ss]
--timestop hh:mm[:ss]
Only match during the given daytime. The possible time range is
00:00:00 to 23:59:59. Leading zeroes are allowed (e.g. "06:03")
and correctly interpreted as base-10.
[!] --monthdays day[,day...]
Only match on the given days of the month. Possible values are 1
to 31. Note that specifying 31 will of course not match on
months which do not have a 31st day; the same goes for 28- or
29-day February.
[!] --weekdays day[,day...]
Only match on the given weekdays. Possible values are Mon, Tue,
Wed, Thu, Fri, Sat, Sun, or values from 1 to 7, respectively.
You may also use two-character variants (Mo, Tu, etc.).
--kerneltz
Use the kernel timezone instead of UTC to determine whether a
packet meets the time regulations.
About kernel timezones: Linux keeps the system time in UTC, and always
does so. On boot, system time is initialized from a referential time
source. Where this time source has no timezone information, such as the
x86 CMOS RTC, UTC will be assumed. If the time source is however not in
UTC, userspace should provide the correct system time and timezone to
the kernel once it has the information.
Local time is a feature on top of the (timezone independent) system
time. Each process has its own idea of local time, specified via the TZ
environment variable. The kernel also has its own timezone offset vari‐
able. The TZ userspace environment variable specifies how the UTC-based
system time is displayed, e.g. when you run date(1), or what you see on
your desktop clock. The TZ string may resolve to different offsets at
different dates, which is what enables the automatic time-jumping in
userspace. when DST changes. The kernel's timezone offset variable is
used when it has to convert between non-UTC sources, such as FAT
filesystems, to UTC (since the latter is what the rest of the system
uses).
The caveat with the kernel timezone is that Linux distributions may
ignore to set the kernel timezone, and instead only set the system
time. Even if a particular distribution does set the timezone at boot,
it is usually does not keep the kernel timezone offset - which is what
changes on DST - up to date. ntpd will not touch the kernel timezone,
so running it will not resolve the issue. As such, one may encounter a
timezone that is always +0000, or one that is wrong half of the time of
the year. As such, using --kerneltz is highly discouraged.
EXAMPLES. To match on weekends, use:
-m time --weekdays Sa,Su
Or, to match (once) on a national holiday block:
-m time --datestart 2007-12-24 --datestop 2007-12-27
Since the stop time is actually inclusive, you would need the following
stop time to not match the first second of the new day:
-m time --datestart 2007-01-01T17:00 --datestop
2007-01-01T23:59:59
During lunch hour:
-m time --timestart 12:30 --timestop 13:30
The fourth Friday in the month:
-m time --weekdays Fr --monthdays 22,23,24,25,26,27,28
(Note that this exploits a certain mathematical property. It is not
possible to say "fourth Thursday OR fourth Friday" in one rule. It is
possible with multiple rules, though.)
tos
This module matches the 8-bit Type of Service field in the IPv4 header
(i.e. including the "Precedence" bits) or the (also 8-bit) Priority
field in the IPv6 header.
[!] --tos value[/mask]
Matches packets with the given TOS mark value. If a mask is
specified, it is logically ANDed with the TOS mark before the
comparison.
[!] --tos symbol
You can specify a symbolic name when using the tos match for
IPv4. The list of recognized TOS names can be obtained by call‐
ing iptables with -m tos -h. Note that this implies a mask of
0x3F, i.e. all but the ECN bits.
u32
U32 tests whether quantities of up to 4 bytes extracted from a packet
have specified values. The specification of what to extract is general
enough to find data at given offsets from tcp headers or payloads.
[!] --u32 tests
The argument amounts to a program in a small language described
below.
tests := location "=" value | tests "&&" location "=" value
value := range | value "," range
range := number | number ":" number
a single number, n, is interpreted the same as n:n. n:m is interpreted
as the range of numbers >=n and <=m.
location := number | location operator number
operator := "&" | "<<" | ">>" | "@"
The operators &, <<, >> and && mean the same as in C. The = is really
a set membership operator and the value syntax describes a set. The @
operator is what allows moving to the next header and is described fur‐
ther below.
There are currently some artificial implementation limits on the size
of the tests:
* no more than 10 of "=" (and 9 "&&"s) in the u32 argument
* no more than 10 ranges (and 9 commas) per value
* no more than 10 numbers (and 9 operators) per location
To describe the meaning of location, imagine the following machine that
interprets it. There are three registers:
A is of type char *, initially the address of the IP header
B and C are unsigned 32 bit integers, initially zero
The instructions are:
number B = number;
C = (*(A+B)<<24) + (*(A+B+1)<<16) + (*(A+B+2)<<8) + *(A+B+3)
&number C = C & number
<< number C = C << number
>> number C = C >> number
@number A = A + C; then do the instruction number
Any access of memory outside [skb->data,skb->end] causes the match to
fail. Otherwise the result of the computation is the final value of C.
Whitespace is allowed but not required in the tests. However, the char‐
acters that do occur there are likely to require shell quoting, so it
is a good idea to enclose the arguments in quotes.
Example:
match IP packets with total length >= 256
The IP header contains a total length field in bytes 2-3.
--u32 "0 & 0xFFFF = 0x100:0xFFFF"
read bytes 0-3
AND that with 0xFFFF (giving bytes 2-3), and test whether that
is in the range [0x100:0xFFFF]
Example: (more realistic, hence more complicated)
match ICMP packets with icmp type 0
First test that it is an ICMP packet, true iff byte 9 (protocol)
= 1
--u32 "6 & 0xFF = 1 && ...
read bytes 6-9, use & to throw away bytes 6-8 and compare the
result to 1. Next test that it is not a fragment. (If so, it
might be part of such a packet but we cannot always tell.) N.B.:
This test is generally needed if you want to match anything
beyond the IP header. The last 6 bits of byte 6 and all of byte
7 are 0 iff this is a complete packet (not a fragment). Alterna‐
tively, you can allow first fragments by only testing the last 5
bits of byte 6.
... 4 & 0x3FFF = 0 && ...
Last test: the first byte past the IP header (the type) is 0.
This is where we have to use the @syntax. The length of the IP
header (IHL) in 32 bit words is stored in the right half of byte
0 of the IP header itself.
... 0 >> 22 & 0x3C @ 0 >> 24 = 0"
The first 0 means read bytes 0-3, >>22 means shift that 22 bits
to the right. Shifting 24 bits would give the first byte, so
only 22 bits is four times that plus a few more bits. &3C then
eliminates the two extra bits on the right and the first four
bits of the first byte. For instance, if IHL=5, then the IP
header is 20 (4 x 5) bytes long. In this case, bytes 0-1 are (in
binary) xxxx0101 yyzzzzzz, >>22 gives the 10 bit value
xxxx0101yy and &3C gives 010100. @ means to use this number as a
new offset into the packet, and read four bytes starting from
there. This is the first 4 bytes of the ICMP payload, of which
byte 0 is the ICMP type. Therefore, we simply shift the value 24
to the right to throw out all but the first byte and compare the
result with 0.
Example:
TCP payload bytes 8-12 is any of 1, 2, 5 or 8
First we test that the packet is a tcp packet (similar to ICMP).
--u32 "6 & 0xFF = 6 && ...
Next, test that it is not a fragment (same as above).
... 0 >> 22 & 0x3C @ 12 >> 26 & 0x3C @ 8 = 1,2,5,8"
0>>22&3C as above computes the number of bytes in the IP header.
@ makes this the new offset into the packet, which is the start
of the TCP header. The length of the TCP header (again in 32 bit
words) is the left half of byte 12 of the TCP header. The
12>>26&3C computes this length in bytes (similar to the IP
header before). "@" makes this the new offset, which is the
start of the TCP payload. Finally, 8 reads bytes 8-12 of the
payload and = checks whether the result is any of 1, 2, 5 or 8.
udp
These extensions can be used if `--protocol udp' is specified. It pro‐
vides the following options:
[!] --source-port,--sport port[:port]
Source port or port range specification. See the description of
the --source-port option of the TCP extension for details.
[!] --destination-port,--dport port[:port]
Destination port or port range specification. See the descrip‐
tion of the --destination-port option of the TCP extension for
details.
TARGET EXTENSIONSip6tables can use extended target modules: the following are included
in the standard distribution.
AUDIT
This target allows to create audit records for packets hitting the tar‐
get. It can be used to record accepted, dropped, and rejected packets.
See auditd(8) for additional details.
--type {accept|drop|reject}
Set type of audit record.
Example:
iptables -N AUDIT_DROP
iptables -A AUDIT_DROP -j AUDIT --type drop
iptables -A AUDIT_DROP -j DROP
CHECKSUM
This target allows to selectively work around broken/old applications.
It can only be used in the mangle table.
--checksum-fill
Compute and fill in the checksum in a packet that lacks a check‐
sum. This is particularly useful, if you need to work around
old applications such as dhcp clients, that do not work well
with checksum offloads, but don't want to disable checksum off‐
load in your device.
CLASSIFY
This module allows you to set the skb->priority value (and thus clas‐
sify the packet into a specific CBQ class).
--set-class major:minor
Set the major and minor class value. The values are always
interpreted as hexadecimal even if no 0x prefix is given.
CONNMARK
This module sets the netfilter mark value associated with a connection.
The mark is 32 bits wide.
--set-xmark value[/mask]
Zero out the bits given by mask and XOR value into the ctmark.
--save-mark [--nfmask nfmask] [--ctmask ctmask]
Copy the packet mark (nfmark) to the connection mark (ctmark)
using the given masks. The new nfmark value is determined as
follows:
ctmark = (ctmark & ~ctmask) ^ (nfmark & nfmask)
i.e. ctmask defines what bits to clear and nfmask what bits of
the nfmark to XOR into the ctmark. ctmask and nfmask default to
0xFFFFFFFF.
--restore-mark [--nfmask nfmask] [--ctmask ctmask]
Copy the connection mark (ctmark) to the packet mark (nfmark)
using the given masks. The new ctmark value is determined as
follows:
nfmark = (nfmark & ~nfmask) ^ (ctmark & ctmask);
i.e. nfmask defines what bits to clear and ctmask what bits of
the ctmark to XOR into the nfmark. ctmask and nfmask default to
0xFFFFFFFF.
--restore-mark is only valid in the mangle table.
The following mnemonics are available for --set-xmark:
--and-mark bits
Binary AND the ctmark with bits. (Mnemonic for --set-xmark
0/invbits, where invbits is the binary negation of bits.)
--or-mark bits
Binary OR the ctmark with bits. (Mnemonic for --set-xmark
bits/bits.)
--xor-mark bits
Binary XOR the ctmark with bits. (Mnemonic for --set-xmark
bits/0.)
--set-mark value[/mask]
Set the connection mark. If a mask is specified then only those
bits set in the mask are modified.
--save-mark [--mask mask]
Copy the nfmark to the ctmark. If a mask is specified, only
those bits are copied.
--restore-mark [--mask mask]
Copy the ctmark to the nfmark. If a mask is specified, only
those bits are copied. This is only valid in the mangle table.
CONNSECMARK
This module copies security markings from packets to connections (if
unlabeled), and from connections back to packets (also only if unla‐
beled). Typically used in conjunction with SECMARK, it is valid in the
security table (for backwards compatibility with older kernels, it is
also valid in the mangle table).
--save If the packet has a security marking, copy it to the connection
if the connection is not marked.
--restore
If the packet does not have a security marking, and the connec‐
tion does, copy the security marking from the connection to the
packet.
CT
The CT target allows to set parameters for a packet or its associated
connection. The target attaches a "template" connection tracking entry
to the packet, which is then used by the conntrack core when initializ‐
ing a new ct entry. This target is thus only valid in the "raw" table.
--notrack
Disables connection tracking for this packet.
--helper name
Use the helper identified by name for the connection. This is
more flexible than loading the conntrack helper modules with
preset ports.
--ctevents event[,...]
Only generate the specified conntrack events for this connec‐
tion. Possible event types are: new, related, destroy, reply,
assured, protoinfo, helper, mark (this refers to the ctmark, not
nfmark), natseqinfo, secmark (ctsecmark).
--expevents event[,...]
Only generate the specified expectation events for this connec‐
tion. Possible event types are: new.
--zone id
Assign this packet to zone id and only have lookups done in that
zone. By default, packets have zone 0.
--timeout name
Use the timeout policy identified by name for the connection.
This is provides more flexible timeout policy definition than
global timeout values available at /proc/sys/net/netfil‐
ter/nf_conntrack_*_timeout_*.
DSCP
This target allows to alter the value of the DSCP bits within the TOS
header of the IPv4 packet. As this manipulates a packet, it can only
be used in the mangle table.
--set-dscp value
Set the DSCP field to a numerical value (can be decimal or hex)
--set-dscp-class class
Set the DSCP field to a DiffServ class.
HL
This is used to modify the Hop Limit field in IPv6 header. The Hop
Limit field is similar to what is known as TTL value in IPv4. Setting
or incrementing the Hop Limit field can potentially be very dangerous,
so it should be avoided at any cost. This target is only valid in man‐
gle table.
Don't ever set or increment the value on packets that leave your local
network!
--hl-set value
Set the Hop Limit to `value'.
--hl-dec value
Decrement the Hop Limit `value' times.
--hl-inc value
Increment the Hop Limit `value' times.
IDLETIMER
This target can be used to identify when interfaces have been idle for
a certain period of time. Timers are identified by labels and are cre‐
ated when a rule is set with a new label. The rules also take a time‐
out value (in seconds) as an option. If more than one rule uses the
same timer label, the timer will be restarted whenever any of the rules
get a hit. One entry for each timer is created in sysfs. This
attribute contains the timer remaining for the timer to expire. The
attributes are located under the xt_idletimer class:
/sys/class/xt_idletimer/timers/<label>
When the timer expires, the target module sends a sysfs notification to
the userspace, which can then decide what to do (eg. disconnect to save
power).
--timeout amount
This is the time in seconds that will trigger the notification.
--label string
This is a unique identifier for the timer. The maximum length
for the label string is 27 characters.
LOG
Turn on kernel logging of matching packets. When this option is set
for a rule, the Linux kernel will print some information on all match‐
ing packets (like most IPv6 IPv6-header fields) via the kernel log
(where it can be read with dmesg or syslogd(8)). This is a "non-termi‐
nating target", i.e. rule traversal continues at the next rule. So if
you want to LOG the packets you refuse, use two separate rules with the
same matching criteria, first using target LOG then DROP (or REJECT).
--log-level level
Level of logging (numeric or see syslog.conf(5)).
--log-prefix prefix
Prefix log messages with the specified prefix; up to 29 letters
long, and useful for distinguishing messages in the logs.
--log-tcp-sequence
Log TCP sequence numbers. This is a security risk if the log is
readable by users.
--log-tcp-options
Log options from the TCP packet header.
--log-ip-options
Log options from the IPv6 packet header.
--log-uid
Log the userid of the process which generated the packet.
MARK
This target is used to set the Netfilter mark value associated with the
packet. It can, for example, be used in conjunction with routing based
on fwmark (needs iproute2). If you plan on doing so, note that the mark
needs to be set in the PREROUTING chain of the mangle table to affect
routing. The mark field is 32 bits wide.
--set-xmark value[/mask]
Zeroes out the bits given by mask and XORs value into the packet
mark ("nfmark"). If mask is omitted, 0xFFFFFFFF is assumed.
--set-mark value[/mask]
Zeroes out the bits given by mask and ORs value into the packet
mark. If mask is omitted, 0xFFFFFFFF is assumed.
The following mnemonics are available:
--and-mark bits
Binary AND the nfmark with bits. (Mnemonic for --set-xmark
0/invbits, where invbits is the binary negation of bits.)
--or-mark bits
Binary OR the nfmark with bits. (Mnemonic for --set-xmark
bits/bits.)
--xor-mark bits
Binary XOR the nfmark with bits. (Mnemonic for --set-xmark
bits/0.)
NFLOG
This target provides logging of matching packets. When this target is
set for a rule, the Linux kernel will pass the packet to the loaded
logging backend to log the packet. This is usually used in combination
with nfnetlink_log as logging backend, which will multicast the packet
through a netlink socket to the specified multicast group. One or more
userspace processes may subscribe to the group to receive the packets.
Like LOG, this is a non-terminating target, i.e. rule traversal contin‐
ues at the next rule.
--nflog-group nlgroup
The netlink group (0 - 2^16-1) to which packets are (only appli‐
cable for nfnetlink_log). The default value is 0.
--nflog-prefix prefix
A prefix string to include in the log message, up to 64 charac‐
ters long, useful for distinguishing messages in the logs.
--nflog-range size
The number of bytes to be copied to userspace (only applicable
for nfnetlink_log). nfnetlink_log instances may specify their
own range, this option overrides it.
--nflog-threshold size
Number of packets to queue inside the kernel before sending them
to userspace (only applicable for nfnetlink_log). Higher values
result in less overhead per packet, but increase delay until the
packets reach userspace. The default value is 1.
NFQUEUE
This target is an extension of the QUEUE target. As opposed to QUEUE,
it allows you to put a packet into any specific queue, identified by
its 16-bit queue number. It can only be used with Kernel versions
2.6.14 or later, since it requires the nfnetlink_queue kernel support.
The queue-balance option was added in Linux 2.6.31, queue-bypass in
2.6.39.
--queue-num value
This specifies the QUEUE number to use. Valid queue numbers are
0 to 65535. The default value is 0.
--queue-balance value:value
This specifies a range of queues to use. Packets are then bal‐
anced across the given queues. This is useful for multicore
systems: start multiple instances of the userspace program on
queues x, x+1, .. x+n and use "--queue-balance x:x+n". Packets
belonging to the same connection are put into the same nfqueue.
--queue-bypass
By default, if no userspace program is listening on an NFQUEUE,
then all packets that are to be queued are dropped. When this
option is used, the NFQUEUE rule is silently bypassed instead.
The packet will move on to the next rule.
NOTRACK
This target disables connection tracking for all packets matching that
rule.
It can only be used in the raw table.
RATEEST
The RATEEST target collects statistics, performs rate estimation calcu‐
lation and saves the results for later evaluation using the rateest
match.
--rateest-name name
Count matched packets into the pool referred to by name, which
is freely choosable.
--rateest-interval amount{s|ms|us}
Rate measurement interval, in seconds, milliseconds or microsec‐
onds.
--rateest-ewmalog value
Rate measurement averaging time constant.
REJECT
This is used to send back an error packet in response to the matched
packet: otherwise it is equivalent to DROP so it is a terminating TAR‐
GET, ending rule traversal. This target is only valid in the INPUT,
FORWARD and OUTPUT chains, and user-defined chains which are only
called from those chains. The following option controls the nature of
the error packet returned:
--reject-with type
The type given can be icmp6-no-route, no-route, icmp6-adm-pro‐
hibited, adm-prohibited, icmp6-addr-unreachable, addr-unreach,
icmp6-port-unreachable or port-unreach which return the appro‐
priate ICMPv6 error message (port-unreach is the default).
Finally, the option tcp-reset can be used on rules which only
match the TCP protocol: this causes a TCP RST packet to be sent
back. This is mainly useful for blocking ident (113/tcp) probes
which frequently occur when sending mail to broken mail hosts
(which won't accept your mail otherwise). tcp-reset can only be
used with kernel versions 2.6.14 or later.
SECMARK
This is used to set the security mark value associated with the packet
for use by security subsystems such as SELinux. It is valid in the
security table (for backwards compatibility with older kernels, it is
also valid in the mangle table). The mark is 32 bits wide.
--selctx security_context
SET
This modules adds and/or deletes entries from IP sets which can be
defined by ipset(8).
--add-set setname flag[,flag...]
add the address(es)/port(s) of the packet to the sets
--del-set setname flag[,flag...]
delete the address(es)/port(s) of the packet from the sets
where flags are src and/or dst specifications and there can be
no more than six of them.
--timeout value
when adding entry, the timeout value to use instead of the
default one from the set definition
--exist
when adding entry if it already exists, reset the timeout value
to the specified one or to the default from the set definition
Use of -j SET requires that ipset kernel support is provided, which,
for standard kernels, is the case since Linux 2.6.39.
TCPMSS
This target allows to alter the MSS value of TCP SYN packets, to con‐
trol the maximum size for that connection (usually limiting it to your
outgoing interface's MTU minus 40 for IPv4 or 60 for IPv6, respec‐
tively). Of course, it can only be used in conjunction with -p tcp.
This target is used to overcome criminally braindead ISPs or servers
which block "ICMP Fragmentation Needed" or "ICMPv6 Packet Too Big"
packets. The symptoms of this problem are that everything works fine
from your Linux firewall/router, but machines behind it can never
exchange large packets:
1. Web browsers connect, then hang with no data received.
2. Small mail works fine, but large emails hang.
3. ssh works fine, but scp hangs after initial handshaking.
Workaround: activate this option and add a rule to your firewall con‐
figuration like:
iptables -t mangle -A FORWARD -p tcp --tcp-flags SYN,RST SYN
-j TCPMSS --clamp-mss-to-pmtu
--set-mss value
Explicitly sets MSS option to specified value. If the MSS of the
packet is already lower than value, it will not be increased
(from Linux 2.6.25 onwards) to avoid more problems with hosts
relying on a proper MSS.
--clamp-mss-to-pmtu
Automatically clamp MSS value to (path_MTU - 40 for IPv4; -60
for IPv6). This may not function as desired where asymmetric
routes with differing path MTU exist — the kernel uses the path
MTU which it would use to send packets from itself to the source
and destination IP addresses. Prior to Linux 2.6.25, only the
path MTU to the destination IP address was considered by this
option; subsequent kernels also consider the path MTU to the
source IP address.
These options are mutually exclusive.
TCPOPTSTRIP
This target will strip TCP options off a TCP packet. (It will actually
replace them by NO-OPs.) As such, you will need to add the -p tcp
parameters.
--strip-options option[,option...]
Strip the given option(s). The options may be specified by TCP
option number or by symbolic name. The list of recognized
options can be obtained by calling iptables with -j TCPOPTSTRIP
-h.
TEE
The TEE target will clone a packet and redirect this clone to another
machine on the local network segment. In other words, the nexthop must
be the target, or you will have to configure the nexthop to forward it
further if so desired.
--gateway ipaddr
Send the cloned packet to the host reachable at the given IP
address. Use of 0.0.0.0 (for IPv4 packets) or :: (IPv6) is
invalid.
To forward all incoming traffic on eth0 to an Network Layer logging
box:
-t mangle -A PREROUTING -i eth0 -j TEE --gateway 2001:db8::1
TOS
This module sets the Type of Service field in the IPv4 header (includ‐
ing the "precedence" bits) or the Priority field in the IPv6 header.
Note that TOS shares the same bits as DSCP and ECN. The TOS target is
only valid in the mangle table.
--set-tos value[/mask]
Zeroes out the bits given by mask (see NOTE below) and XORs
value into the TOS/Priority field. If mask is omitted, 0xFF is
assumed.
--set-tos symbol
You can specify a symbolic name when using the TOS target for
IPv4. It implies a mask of 0xFF (see NOTE below). The list of
recognized TOS names can be obtained by calling iptables with -j
TOS -h.
The following mnemonics are available:
--and-tos bits
Binary AND the TOS value with bits. (Mnemonic for --set-tos
0/invbits, where invbits is the binary negation of bits. See
NOTE below.)
--or-tos bits
Binary OR the TOS value with bits. (Mnemonic for --set-tos
bits/bits. See NOTE below.)
--xor-tos bits
Binary XOR the TOS value with bits. (Mnemonic for --set-tos
bits/0. See NOTE below.)
NOTE: In Linux kernels up to and including 2.6.38, with the exception
of longterm releases 2.6.32 (>=.42), 2.6.33 (>=.15), and 2.6.35
(>=.14), there is a bug whereby IPv6 TOS mangling does not behave as
documented and differs from the IPv4 version. The TOS mask indicates
the bits one wants to zero out, so it needs to be inverted before
applying it to the original TOS field. However, the aformentioned ker‐
nels forgo the inversion which breaks --set-tos and its mnemonics.
TPROXY
This target is only valid in the mangle table, in the PREROUTING chain
and user-defined chains which are only called from this chain. It redi‐
rects the packet to a local socket without changing the packet header
in any way. It can also change the mark value which can then be used in
advanced routing rules. It takes three options:
--on-port port
This specifies a destination port to use. It is a required
option, 0 means the new destination port is the same as the
original. This is only valid if the rule also specifies -p tcp
or -p udp.
--on-ip address
This specifies a destination address to use. By default the
address is the IP address of the incoming interface. This is
only valid if the rule also specifies -p tcp or -p udp.
--tproxy-mark value[/mask]
Marks packets with the given value/mask. The fwmark value set
here can be used by advanced routing. (Required for transparent
proxying to work: otherwise these packets will get forwarded,
which is probably not what you want.)
TRACE
This target marks packets so that the kernel will log every rule which
match the packets as those traverse the tables, chains, rules.
A logging backend, such as ip(6)t_LOG or nfnetlink_log, must be loaded
for this to be visible. The packets are logged with the string prefix:
"TRACE: tablename:chainname:type:rulenum " where type can be "rule" for
plain rule, "return" for implicit rule at the end of a user defined
chain and "policy" for the policy of the built in chains.
It can only be used in the raw table.
DIAGNOSTICS
Various error messages are printed to standard error. The exit code is
0 for correct functioning. Errors which appear to be caused by invalid
or abused command line parameters cause an exit code of 2, and other
errors cause an exit code of 1.
BUGS
Bugs? What's this? ;-) Well... the counters are not reliable on
sparc64.
COMPATIBILITY WITH IPCHAINS
This ip6tables is very similar to ipchains by Rusty Russell. The main
difference is that the chains INPUT and OUTPUT are only traversed for
packets coming into the local host and originating from the local host
respectively. Hence every packet only passes through one of the three
chains (except loopback traffic, which involves both INPUT and OUTPUT
chains); previously a forwarded packet would pass through all three.
The other main difference is that -i refers to the input interface; -o
refers to the output interface, and both are available for packets
entering the FORWARD chain. There are several other changes in
ip6tables.
SEE ALSOip6tables-save(8), ip6tables-restore(8), iptables(8), iptables-save(8),
iptables-restore(8), libipq(3).
The packet-filtering-HOWTO details iptables usage for packet filtering,
the netfilter-extensions-HOWTO details the extensions that are not in
the standard distribution, and the netfilter-hacking-HOWTO details the
netfilter internals.
See http://www.netfilter.org/.
AUTHORS
Rusty Russell wrote iptables, in early consultation with Michael Neul‐
ing.
Marc Boucher made Rusty abandon ipnatctl by lobbying for a generic
packet selection framework in iptables, then wrote the mangle table,
the owner match, the mark stuff, and ran around doing cool stuff every‐
where.
James Morris wrote the TOS target, and tos match.
Jozsef Kadlecsik wrote the REJECT target.
Harald Welte wrote the ULOG and NFQUEUE target, the new libiptc, as
well as TTL match+target and libipulog.
The Netfilter Core Team is: Marc Boucher, Martin Josefsson, Yasuyuki
Kozakai, Jozsef Kadlecsik, Patrick McHardy, James Morris, Pablo Neira
Ayuso, Harald Welte and Rusty Russell.
ip6tables man page created by Andras Kis-Szabo, based on iptables man
page written by Herve Eychenne <rv@wallfire.org>.
VERSION
This manual page applies to ip6tables @PACKAGE_VERSION@.
iptables 1.4.14IP6TABLES(8)
