leafnode(8)leafnode(8)NAMEleafnode - NNTP server for small (dialup) sites
SYNOPSISleafnodeDESCRIPTION
Leafnode is a USENET package intended for small sites, where there are
few users and little disk space, but where a large number of groups is
desired.
The design of leafnode is intended to self-repair after problems, and
to require no manual maintenance.
The leafnode program itself is the NNTP server. It is run from
inetd(8), xinetd(8) or tcpserver when someone wants to read news. The
other parts of the package, fetchnews and texpire, are responsible for
fetching new news from another server, and for deleting old news.
ACCESS CONTROL
No authentication or access control is supported. This is a deliberate
omission: Implementing this is a job which should not be redone for
each and every service.
It is mandatory that you use external access control mechanisms like
tcpd, inetd/xinetd compiled with libwrap support, tcpserver with -x
option and the like and that these are in effect. tcpd and libwrap are
components of Wietse Venema's fine tcp_wrappers package.
As a very rough last line of defense against abuse, leafnode will drop
connections from outside your LANs by default. You can configure leafn‐
ode to let go of this restriction (look for the allowstrangers option),
but don't do that unless tight access control is in place. Someone
will abuse your computer sooner or later. Promised.
I recommend that either firewalling or tcpd be used for access control.
FILES
All these files and directories must be readable by the user "news". It
is recommended that, unless otherwise stated, that the user "news" be
the only user in the group "news" and these files belong to "root:news"
(user:group) so leafnode cannot modify your configuration or filter
files.
/etc/leafnode should not be writable by the user "news", but it must be
executable for at least any of the group that the user "news" is in.
/etc/leafnode/config contains the configuration parameters for leafn‐
ode. It must not be writable by the user "news". Set this to owner
root:news and mode 640. For details, see CONFIGURATION below.
/var/spool/news must also be readable and writable by the user "news".
It contains the news articles; e.g. /var/spool/news/alt/fan/agulbra
contains the articles in the alt.fan.agulbra group. Each directory
contains articles in numbered files (decimal numbers, monotonically
increasing), and a special file called .overview which contains the
"Subject", "From", "Date", "Message-ID", "References", "Bytes" and
"Lines" headers for each article in the group.
Several subdirectories are special:
/var/spool/news/leaf.node contains the files that leafnode creates dur‐
ing operation, for example the groupinfo file which contains informa‐
tion about each USENET newsgroup. This file is built by fetchnews (8).
You can force a complete rebuild of the groupinfo file by calling
fetchnews with the parameter -f (see fetchnews (8)).
/var/spool/news/out.going contains local postings that fetchnews(8) is
to pass to the upstream NNTP server. After a posting has been success‐
fully written to disk, its u+r permission flag is set. This flag is
interpreted by fetchnews(8) as "you may post this article". This pre‐
vents fetchnews from posting articles that are still being received
from newsreaders. (Note: versions 1.9.23 to 1.9.32 inclusively used u+x
instead, which caused some "stuck post" problems with articles in the
spool when a prior leafnode version was updated to one of these 10 ver‐
sions. Updating to leafnode 1.9.33 or later fixes the problem.)
/var/spool/news/failed.postings contains local postings that the
upstream server rejected. fetchnews(8) will create files in this
directory, but none of the leafnode programs will delete anything in
it.
/var/spool/news/message.id contains hard links to each message; this is
used in place of the dbz database typically used by bigger servers. (A
directory such as this is probably more efficient for the small servers
leafnode is designed for but scales very badly.)
/var/spool/news/interesting.groups contains one file for each group an
NNTP client has asked to read. leafnode will update the ctime (ls -l
usually shows the mtime, try ls -lc) of the relevant file when a LIST‐
GROUP, XOVER, XHDR, STAT, HEAD, BODY or ARTICLE command is issued, when
a GROUP or LIST ACTIVE command (the latter only with a single group,
not with patterns) is issued for an interesting group (to avoid unsub‐
scribing low-traffic groups that are still read) and fetchnews(8) will
retrieve all new articles in all groups whose files have been either
- touched during the past two days, or
- touched more than once, and at least once within the past
week.
The timeout is configurable through the config file variables time‐
out_short and timeout_long. See also fetchnews(8) for the -n option.
/etc/inetd.conf or /etc/xinetd.conf contains the configuration which
starts leafnode. It is strongly recommended to start leafnode as user
news.
ENVIRONMENT
LN_REJECT_POST_PRE
If this variable exists, all POST commands are rejected with a
400 code. Use only for debugging clients.
LN_REJECT_POST_POST
If this variable exists, the POST command is rejected with a 400
code after the article and CRLF.CRLF has been received. Use only
for debugging clients.
CONFIGURATION
All configuration is done using the file /etc/leafnode/config, which
may include a filter description file, filterfile for short, as
described below.
For the purposes of this section, whitespace shall be defined as an
arbitrary sequence consisting of one or more SPACE or HTAB characters,
ASCII positions 32 and 9, respectively.
The configuration file is strictly line-oriented with LF or CRLF as
line terminator.
Empty lines and lines consisting of only whitespace, possibly followed
by a comment (introduced by a hash mark (#) and extending through the
end of the line), are skipped.
All other lines have exactly three mandatory fields, a plain text
parameter, an assignment character (=) optionally surrounded by white‐
space and a value. The value is either plain text or - new since
leafnode v1.11 - a string in double quotes with trivial backslash
escape (see below).
Plain text starts at the first non-whitespace character and extends
through the last non-whitespace character on the line that is not a
comment. A trailing comment on a line is skipped.
Quoted strings are enclosed in double quote characters ("). The back‐
slash character (\) is skipped, but it copies the immediately following
character verbatim, so that you can specify the backslash itself by
doubling it (\\) or a double quote character as part of the string by
preceding it with a backslash (\"); the hash mark has no special mean‐
ing as command introducer inside quoted strings. Text after the end of
the string is silently ignored (this may change in future versions).
Comments after quoted strings are ignored.
MANDATORY PARAMETERS
These parameters must be specified for leafnode to work.
server = news02.example.com
"server" is used by fetchnews (8) to select what NNTP server(s)
to retrieve news from and to post your articles to. You can
specify more than one news server; in that case, the servers
will be queried from the top down. If you want to post articles,
at least one of your servers should allow you to post. In the
example above, news02.example.com is the news server.
This parameter can be given more than once. Each server starts
with a fresh set of default configuration options, no inheri‐
tance takes place from the previous server definition. Only
options explicitly marked "server-specific" can be set on a per
server basis, "general" options are set for all servers at the
same time.
expire = 5
"expire" is the number of days an article should be kept around.
In the example, five days after the article has last been read,
it is deleted by texpire (8). This value MUST be at least 1.
This parameter is global, see the introductory paragraph of the
following GENERAL OPTION PARAMETERS section to find out what
this means.
GENERAL OPTIONAL PARAMETERS
These options can only be configured once in the configuration file,
and take effect for leafnode as a whole. It does not matter where these
are specified relative to server= options, but for clarity, you are
encouraged to place these before the first server= line. Specifying
each of the global options more than once lets the last copy take
effect, but may cause errors in the future.
hostname = host.domain.country
By default, leafnode tries hard to figure the host name of your
computer, skipping inadequate (non-unique) names if possible. It
will look up your computer's host name with gethostname(3) and
then try to qualify the name with gethostbyname(3) if necessary.
Common sources for the full name therefore are /etc/hosts, NIS
and DNS, but consult your system documentation for details.
If leafnode fails to determine the host name, this is usually a
hint that your system is not configured properly, or it has a
hostname that is unsuitable for the domain part of a Message-ID,
for example, "localhost.localdomain", and you should fix the
name service configuration. Adding a unique fully-qualified host
name to /etc/hosts is usually sufficient. Please see README-FQDN
for more details.
You can configure the unique fully-qualified host name here as
well, but this is not recommended and discouraged.
create_all_links = 1
Normally, fetchnews will store articles only in the newsgroups
which it considers interesting. With this option set, fetchnews
will create hardlinks for all newsgroups in the Newsgroups:
header that it knows about. This may be of interest if you want
to apply a score- or killfile to the local Xref: line.
maxfetch = 1000
"maxfetch" specifies the maximum number of articles fetchnews
(8) should fetch from the upstream server in each group. Its use
is not advised, because if you use it you will not see all the
traffic in a group. By default there is no limit.
initialfetch = 1
"initialfetch" defines how many articles from a newly subscribed
group should be fetched. The default is to fetch all old arti‐
cles, which can get quite time-consuming when subscribing to a
very busy group. This is equivalent to setting initialfetch to
zero. If you want to get no old articles when subscribing to a
new group, you should set initialfetch to one, as in the example
above.
groupexpire very.crowded.group = 1
groupexpire very.crowded.hierarchy.* = 1
"groupexpire" makes it possible to adjust expiry times for indi‐
vidual groups. Expiry times are given in days. 0 means "use the
default", negative values prevent the expire process for this
group altogether (you can consider this an archive mode). This
value is used by texpire (8). You can specify as many groupex‐
pire lines as you like. It is possible to specify glob (7)-like
wildcard expressions.
maxage = 10
If an article turns up on your upstream news server which is
older than "maxage" days it will not been fetched even if you
don't have it yet. This is useful if your upstream server gets
occasional "hiccups". The default is set to 10. If you want to
switch this feature off, set maxage to some very large value,
such as 20000 (this is equivalent to roughly 54 years).
maxold = 10
Is synonymous to maxage, see above.
maxlines = 2000
If you want to avoid receiving very large articles, you may set
the "maxlines" parameter to the maximal number of lines an arti‐
cle should have. By default, this feature is switched off.
minlines = 2
Sometimes newsgroups are spammed with empty postings. To reject
these postings, you can set the "minlines" parameter. Setting
minlines to a value larger 4 is probably not a good idea since
you will also start to kill "real" postings then. By default,
this feature is switched off.
maxbytes = 100000
If you want to avoid receiving very large articles, instead of
using the "maxlines" parameter you can also use the "maxbytes"
parameter. By default, this feature is switched off.
maxcrosspost = 5
If you want to combat spam, you can filter out all postings that
are posted to more than a certain number of newsgroups. The num‐
ber is defined by setting "maxcrosspost". Setting this parameter
to very low values is probably a bad idea. This feature is
switched off by default.
maxgroups = 5
Synonymous for maxcrosspost. See above.
filterfile = /etc/leafnode/filters
Leafnode can filter the input headers for arbitrary regular
expressions. These are stored in a file designated "filter‐
file". The format of "filterfile" is very simple: one perl-com‐
patible regular expression per line. If one of the regular
expressions fits to a header to be downloaded, the body of that
article will be rejected. This feature is switched off by
default. The format of the regular expressions is described in
pcre(3).
timeout_short = 2
By default, a group that has been accidentally touched is being
fetched for two days. You can change this time by changing time‐
out_short.
timeout_long = 7
By default, a group that has not been read at all is being
fetched for seven days before being unsubscribed. This interval
can be changed by setting timeout_long to a different value.
timeout_active = 90
By default, active files from the upstream servers are re-read
every 90 days. This interval can be changed by setting time‐
out_active to a different value. Be aware that reading an active
file transfers about one MB of information if the server that
you are using carries a reasonable number of groups (i. e.
around 20,000).
timeout_client = 900 (since v1.9.23)
By default, leafnode will drop the connection 900 seconds (15
minutes) after seeing the last command from the client. You can
change the timeout here. Setting it too low (like below 5 min‐
utes) will annoy your users and consume more system resources
for re-reading all the files.
timeout_fetchnews = 300 (since v1.9.52)
Fetchnews will, since v1.9.52, assume the upstream server has
become wedged after waiting for a reply for 300 seconds. You can
change the timeout here.
timeout_lock = 5 (since v1.9.54)
Configure how many seconds the leafnode programs (applyfilter,
checkgroups, fetchnews, texpire) will wait for the lock file
before aborting. Setting this to 0 means to wait indefinitely.
NOTE: you can override this by setting the environment variable
LN_LOCK_TIMEOUT (note it is not LN_TIMEOUT_LOCK). The default
is 5 seconds.
delaybody = 1
With this option set, fetchnews (8) fetches only the headers of
an article for visual inspection. Only when the headers have
been read, the bodies of the articles will be retrieved the next
time fetchnews (8) is called. This can save a huge amount of
download time and disk space.
delaybody_in_situ = 1 (since v1.9.41)
This is only applicable with delaybody=1.
By default, leafnode will give the full downloaded article a new
article number so they appear as new in your newsreader. This
does not work for all newsreaders. With this option set, leafn‐
ode will retain the original article number. You'll have to fig‐
ure out how to tell your newsreader to show old articles. This
option defaults to 0. It is highly recommended to leave it
unset.
debugmode = 1
With this option set, fetchnews (8), texpire (8) and leafnode
(8) will start to log lots of debugging output via syslog (8) at
facility news and priority debug. Use it for tracking down prob‐
lems with your feed. debugmode should be left at 0 for regular
use because it can log enormous amounts of data. The higher the
number, the more will be logged. Choosing a figure greater than
3 will not make a difference at the moment.
allow_8bit_headers = 1 (since v1.9.25)
By default, leafnode rejects local posts that have 8-bit charac‐
ters in their headers, because they violate relevant standards,
particularly RFC-2822 (which RFC-1036 is based on) that demands
that Usenet news headers (as mail headers) must be pure 7-bit
US-ASCII, with only whitespace allowed from the control charac‐
ters.
However, as UTF-8 is to come, and some national hierarchies,
particularly the Norwegian and Danish (no.*, dk.*) seem to have
agreed on preferring just-send-eight over RFC-2047, you can set
this option to allow 8-bit data in headers. Leafnode will how‐
ever add a warning header if 8-bit data is present, stating that
the site administrator allowed this.
There is no way to make leafnode accept non-whitespace control
characters in headers.
allowSTRANGERS = MAGIC (since v1.9.23)
By default, leafnode refuses connections from outside your LANs.
Check config.example for how to use this parameter to let
strangers connect to your leafnode. Instead of MAGIC, you have
to write a number as mentioned in config.example. Note that cap‐
italization matters.
linebuffer = 1
By default, stdout and sometimes stderr of applications are set
to "fully buffered" unless connected to terminals. Use this
option to explicitly request line buffered mode for stdout and
stderr.
clamp_maxage = 0
By default, leafnode will derive a "maxage" argument from the
expire time that is applicable to the group (groupexpire if set,
expire otherwise), to prevent fetching articles again that were
once there and then cleared by texpire(8). Set clamp_maxage=0 to
get rid of this behaviour.
article_despite_filter = 1 (since v1.9.33)
By default, fetchnews will request HEAD and BODY separately if a
filter file is defined and delaybody is off. For high latency,
high throughput links (such as interleaved DSL or satellite
links), it may be faster to request head and body together with
an ARTICLE command and ignore the body if the filters apply
(though it may not be cheaper if you pay per MByte), enabling
this option will force leafnode to use the ARTICLE command in
spite of filters being defined. (Note that in delaybody mode,
HEAD and BODY will ALWAYS be requested separately.)
newsadmin = news@leafnode.example.org (since v1.9.47)
This option sets the From: address for the placeholder article,
it should be the news administrator's mail address. It defaults
to news@HOSTNAME, where HOSTNAME is leafnode's hostname.
SERVER-SPECIFIC OPTIONAL PARAMETERS
These options can only be placed after the server= line of the server
to which you would like these to apply, and they always pertain to the
preceding server= line. Specifying them before the first server= line
is an error.
username = myname
If any of your news servers requires authentication, you can
enter your username on that server here. This field may occur
multiple times, once after each server definition. See the
introduction of this CONFIGURATION section for information on
how to quote myname.
password = mypassword
If any of your news servers requires authentication, you can
enter your password on that server here. This field may occur
multiple times, once after each server definition. Since the
password is available in clear text, it is recommended that you
set the rights on the config file as restrictive as possible,
otherwise other users of your computer will be able to get your
password(s) from that file. See the introduction of this CONFIG‐
URATION section for information on how to quote mypassword.
port = 8000
By default, fetchnews tries to connect to its upstream news
servers on the NNTP port (119). If your servers run on a differ‐
ent port, you can specify those here. This field may occur mul‐
tiple times, once after each server definition.
Note: to modify the port your own leafnode servers listens on,
change the inetd.conf, xinetd.conf configuration file or the
tcpsvd/tcpserver command line. leafnode does not set up its lis‐
ten port itself.
timeout = 30
By default, leafnode tries to connect for 10 seconds to a server
and then gives up. If you have a slow server, you can try for a
longer time by setting the timeout higher (in this example, 30
seconds). The timeout can be tuned individually for each server.
noactive = ANYTHING (v1.9.25 ... v1.11.4)
noactive = 1 (since v1.11.5)
If this parameter is set, the active file is never downloaded
from this server. Use this for very slow servers unless they
carry groups that other servers don't offer. Leafnode versions
1.9.25 to 1.11.4 would always assume that "ANYTHING" had been 1.
"noactive = 0" is supported since v1.11.5.
nodesc = ANYTHING (until v1.11.4)
nodesc = 1 (since v1.11.5)
Some servers do not deliver news groups descriptions correctly
because they cannot parse the XGTITLE and LIST NEWSGROUPS com‐
mands. In that case, put this line after the "server" line.
Leafnode versions up to v1.11.4 would always assume that "ANY‐
THING" had been 1. "nodesc = 0" is supported since v1.11.5.
nopost = 1 (since v1.9.23)
Prevent posting to this server. You can use this if the upstream
won't let you post but still greet leafnode with 200 or if the
upstream doesn't forward your postings reliably.
noread = 1 (since v1.9.33)
Prevent fetching news articles or active files from this server.
You can use this if the upstream is good to post, but too slow
to fetch news from.
noxover = 1 (since v1.9.47)
Prevent the use of XOVER on the current server. Fetchnews will
use XHDR instead.
only_groups_match_all = 1 (since v1.9.52)
Usually, when cross-posting an article, fetchnews will post the
article if ANY group listed in the Newsgroups: header is matched
by the PCRE. With this option on, ALL groups listed in the
Newsgroups: header must match. This can be used to avoid "poi‐
son" groups when you have multiple upstream servers.
only_groups_pcre = PCRE (since v1.9.28)
This parameter lists the Perl-compatible regular expression of
groups that are fetched or posted to this server. The PCRE is
automatically anchored at the left hand side, so you can omit
the leading ^. Remember to escape dots, as in:
de\.comp\.|de\.comm\.
If this parameter is omitted, all groups are fetched from and
posted to this server.
Note: you must run fetchnews with the -f option after changing,
adding or removing any only_groups_pcre option.
Hint: you can use something like this to check your
only_groups_pcre settings:
cut -f1 -d" " @spooldir@/leaf.node/groupinfo \
| pcregrep 'PATTERN'
post_anygroup = 1 (since v1.9.37)
This parameter makes leafnode post on this server without check‐
ing if it carries the group an article is posted to. The default
is post_anygroup = 0, which means that leafnode will check with
a "GROUP" command if the server carries the group the articles
is posted into. Use this on post-only servers that don't allow
the "GROUP" command. Note: inconsiderate use of this parameter
may cause articles to end up in the failed.postings directory.
OBSOLETE PARAMETERS
supplement
is synonymous to server. Don't use it on new installations.
fqdn is synonymous to hostname. Don't use it on new installations.
PROTOCOL
Here are the NNTP commands supported by this server:
ARTICLE, BODY, DATE, GROUP, HDR, HEAD, HELP, LAST, LIST, LIST ACTIVE,
LIST ACTIVE.TIMES, LIST EXTENSIONS, LIST NEWSGROUPS, LIST OVERVIEW.FMT,
LISTGROUP, MODE, NEWGROUPS, NEXT, POST, OVER, SLAVE, STAT, XHDR, XOVER.
These commands follow RFC-977 and RFC-2980, except HDR and OVER which
are recognized in anticipation of current NNTP drafts.
Note that the syntax of HDR and OVER may change.
BUGS
Leafnode is totally unaware of UTF-8 and will reject a client that
posts UTF-8 characters in the header. Current Usefor drafts claim all
article headers UTF-8 encoded Unicode. Leafnode still expects RFC-2047
instead which may eventually be phased out in favour of UTF-8.
Leafnode stops reading a line at the first NUL character.
Leafnode may not cope well with crosspostings that cross hierarchies if
you have multiple upstream feeds and use the only_groups_pcre configu‐
ration option.
Leafnode will only bother to determine the time zone offset for gener‐
ated Date: headers for posts that lack them on systems that offer the
tm_gmtoff member in struct tm (commonly BSD and GNU systems).
AUTHOR
Written by Arnt Gulbrandsen <agulbra@troll.no> and copyright 1995 Troll
Tech AS, Postboks 6133 Etterstad, 0602 Oslo, Norway, fax +47 22646949.
Modified by Cornelius Krasel <krasel@wpxx02.toxi.uni-wuerzburg.de>,
Randolf Skerka <Randolf.Skerka@gmx.de> and Markus Enzenberger
<enz@cip.physik.uni-muenchen.de>. Copyright of the modifications
1997-1999.
Modified by Matthias Andree <matthias.andree@gmx.de>, Copyright 1999 -
2002. Modified by Ralf Wildenhues <ralf.wildenhues@gmx.de>, Copyright
2002.
Jonathan Larmour <jifl@jifvik.org> contributed the timeout_client fea‐
ture.
Andreas Meininger <a.meininger@gmx.net> contributed the code to let
texpire ignore groupexpire = -1 groups.
Mark Brown <broonie@debian.org> added the noactive option.
Numerous contributions by other people.
The initial development of leafnode has been paid for by Uninett AS
(http://www.uninett.no/).
SEE ALSOapplyfilter(8), checkgroups(8), fetchnews(8), newsq(1), texpire(8).
tcpd(8), hosts_access(5), glob(7), pcre(3), RFC 977, RFC 2980.
leafnode 1.11.8 leafnode(8)
