mkswap man page on SuSE

Man page or keyword search:  
man Server   14857 pages
apropos Keyword Search (all sections)
Output format
SuSE logo
[printable version]

MKSWAP(8)		   Linux Programmer's Manual		     MKSWAP(8)

NAME
       mkswap - set up a Linux swap area

SYNOPSIS
       mkswap [-c] [-f] [-p PSZ] [-L label] [-U uuid] device [size]

DESCRIPTION
       mkswap sets up a Linux swap area on a device or in a file.

       The  device  argument  will usually be a disk partition (something like
       /dev/sdb7) but can also be a file.  The Linux kernel does not  look  at
       partition  IDs,	but  many installation scripts will assume that parti‐
       tions of hex type 82 (LINUX_SWAP) are  meant  to	 be  swap  partitions.
       (Warning:  Solaris  also	 uses  this type.  Be careful not to kill your
       Solaris partitions.)

       The size parameter is superfluous but retained for  backwards  compati‐
       bility.	 (It  specifies the desired size of the swap area in 1024-byte
       blocks.	mkswap will use the entire partition or file if it is omitted.
       Specifying it is unwise -- a typo may destroy your disk.)

       The  PSZ parameter specifies the page size to use.  It is almost always
       unnecessary (even unwise) to specify it, but certain old libc  versions
       lie  about  the page size, so it is possible that mkswap gets it wrong.
       The symptom is that a subsequent swapon fails because no swap signature
       is found.  Typical values for PSZ are 4096 or 8192.

       After  creating	the  swap  area,  you need the swapon command to start
       using it.  Usually swap areas are listed in /etc/fstab so that they can
       be  taken  into	use  at	 boot time by a swapon -a command in some boot
       script.

WARNING
       The swap header does not touch the first block.	A boot loader or  disk
       label can be there, but it is not a recommended setup.  The recommended
       setup is to use a separate partition for a Linux swap area.

       mkswap, like many others mkfs-like utils, erases	 the  first  block  to
       remove old on-disk filesystems.

       mkswap  refuses	to erase the first block on a device with a disk label
       (SUN, BSD, ...) or on a whole disk (e.g. /dev/sda).

OPTIONS
       -c     Check the device (if it is a block device) for bad blocks before
	      creating the swap area.  If any are found, the count is printed.

       -f     Force  --	 go  ahead even if the command is stupid.  This allows
	      the creation of a swap area larger than the file or partition it
	      resides on.

	      Without this option, mkswap will refuse to erase the first block
	      on a device with a partition table or  on	 a  whole  disk	 (e.g.
	      /dev/sda).

       -L label
	      Specify a label, to allow swapon by label.

       -p PSZ Specify the page size (in bytes) to use.	This option is usually
	      unnecessary, mkswap reads the size from the kernel.

       -U uuid
	      Specify the uuid to use.	The default is to generate a UUID.

       -v1    Specify the swap-space version.  The old -v0 option  has	become
	      obsolete and now only -v1 is supported.

	      The  kernel has not supported v0 swap-space format since 2.5.22.
	      The new version v1 is supported since 2.1.117.

NOTES
       The maximum useful size of a swap area depends on the architecture  and
       the  kernel  version.   It  is roughly 2GiB on i386, PPC, m68k and ARM,
       1GiB on sparc, 512MiB on mips, 128GiB on alpha, and  3TiB  on  sparc64.
       For kernels after 2.3.3 there is no such limitation.

       Note that before version 2.1.117 the kernel allocated one byte for each
       page, while it now allocates two bytes, so that taking into use a  swap
       area of 2 GiB might require 2 MiB of kernel memory.

       Presently, Linux allows 32 swap areas (this was 8 before Linux 2.4.10).
       The areas in use can be seen in the file /proc/swaps (since 2.1.25).

       mkswap refuses areas smaller than 10 pages.

       If you don't know the page size that your machine uses, you may be able
       to  look it up with "cat /proc/cpuinfo" (or you may not -- the contents
       of this file depend on architecture and kernel version).

       To set up a swap file, it is necessary to create that file before  ini‐
       tializing it with mkswap, e.g. using a command like

	      # dd if=/dev/zero of=swapfile bs=1024 count=65536

       Note  that  a  swap file must not contain any holes (so, using cp(1) to
       create the file is not acceptable).

SEE ALSO
       fdisk(8), swapon(8)

AVAILABILITY
       The mkswap command is part of the util-linux package and	 is  available
       from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.

Linux				 13 March 2009			     MKSWAP(8)
[top]

List of man pages available for SuSE

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net