PCIBIOS(4) OpenBSD Programmer's Manual (i386) PCIBIOS(4)NAMEpcibios - introduction to PCI BIOS support
SYNOPSIS
pcibios0 at bios0 flags 0x0000
DESCRIPTION
OpenBSD provides support for setting up PCI controllers, bridges, and
devices using information extracted from the BIOS.
Ideally, the boot firmware of a machine (a.k.a. BIOS) should set up all
PCI devices; assigning them I/O and memory addresses and interrupts.
Alas, this does not always happen, so there is some PC specific code that
can do the initialization when OpenBSD boots.
Flags is a bit mask each bit of which specifies a fixup procedure to
omit. The following list specifies these procedures and gives flags bit
values to disable them in case they cause problems.
0x0001 Fixup PCI I/O and memory addresses.
Some BIOS implementations don't allocate I/O space and memory
space for all PCI devices. Especially, a BIOS which has "PnP OS
mode" enabled shows this behavior. Since necessary space isn't
allocated, those devices will not work without special handling.
Without this flag force allocation of I/O space and memory space
instead of relying upon the BIOS to do so.
If necessary space is already correctly assigned to the devices,
this option leaves the space as is.
Although many BIOS implementations leave CardBus bridges' space
unallocated, the CardBus bridge device driver doesn't require
this option, since the driver allocates necessary space by
itself.
0x0002 Fixup PCI bus numbering; needed for many cardbus(4) bridges.
Each PCI bus and CardBus should have a unique bus number. But
some BIOS implementations don't assign a bus number for
subordinate PCI buses. And many BIOS implementations don't
assign a bus number for CardBuses.
A typical symptom of this is the following boot message:
cardbus0 at cardslot0: bus 0 device 0...
Please note that this cardbus0 has a bus number `0', but normally
the bus number 0 is used by the machine's primary PCI bus. Thus,
this bus number for cardbus is incorrect (not assigned). In this
situation, a device located in cardbus0 doesn't show correct
device ID, because its bus number 0 incorrectly refers to the
primary PCI bus, and a device ID in the primary PCI bus is shown
in the boot message instead of the device's ID in the cardbus0.
Without this flag force assignment of bus numbers for all
subordinate PCI buses and CardBuses.
Since this procedure renumbers all PCI buses and CardBuses, all
bus numbers of subordinate buses become different when this
option is enabled.
0x0004 Fixup PCI interrupt routing.
Some BIOS implementations don't assign an interrupt for some
devices.
This procedure assigns an interrupt for such devices instead of
relying upon the BIOS to do so.
If the BIOS has already assigned an interrupt to a device, this
procedure leaves the interrupt as is.
0x0008 Make PCI interrupt routing fixup work with unknown interrupt
routers. If this flag is specified and a PCI interrupt routing
table entry indicates that only one IRQ is available for the
entry, the IRQ is assumed to be already connected to the device,
and the corresponding PCI Interrupt Configuration Register will
be configured accordingly.
Without this flag, if a PCI interrupt router is not known,
interrupt configuration will not be modified.
0x0010 Be verbose when performing pcibios tasks. Included in these
diagnostics are: PCI device address fixup tables, interrupt fixup
reports, and other diagnostic and non-fatal messages.
0x0020 Make the PCI interrupt routing fixup procedure verbose.
0x0040 Some buggy BIOS implementations provide inconsistent information
between the PCI Interrupt Configuration Register and the PCI
Interrupt Routing table. In such cases, the PCI Interrupt
Configuration Register takes precedence by default. If this flag
is specified the PCI Interrupt Routing table takes precedence.
SEE ALSObios(4), intro(4), pci(4), pci_conf_read(9), pci_intr_map(9)HISTORY
The pcibios code appeared in NetBSD 1.5. OpenBSD support was added in
OpenBSD 2.8. In contrast to NetBSD implementation pcibios in OpenBSD is
a real device, where options control is done through the flags which are
modifiable through the boot_config(8) interface. For OpenBSD 2.9 the PCI
interrupt routing establishment sequence was redone to only fixup and
route interrupts when attaching interrupts for a particular PCI device.
BUGS
The PCIBIOS Address Fixup option may conflict with the PCI CardBus
driver's own address fixup.
OpenBSD 4.9 July 1, 2008 OpenBSD 4.9
