rrenumd.conf man page on FreeBSD

Man page or keyword search:  
man Server   9747 pages
apropos Keyword Search (all sections)
Output format
FreeBSD logo
[printable version]

RRENUMD.CONF(5)		    BSD File Formats Manual	       RRENUMD.CONF(5)

NAME
     rrenumd.conf — configuration file for router renumbering daemon

DESCRIPTION
     The rrenumd config file describes how the router renumbering packet must
     be constructed and to which destinations it should be sent.  This file
     consists of a sequence of statements terminated by a semi-colon (`;').
     Statements are composed of tokens separated by white space, which can be
     any combination of blanks, tabs and newlines.  This structure simplifies
     identification of the parts of the configuration associated with each
     other.  Lines beginning with ‘#’ are comments.

Meta Syntax
     Keywords and special characters that the parser expects exactly are dis‐
     played using the bold font.  Parameters are specifying with underline.
     Parameters shown in square brackets (`[' and `]') are used to show
     optional keywords and parameters.	The vertical bar (`|') is used to
     indicate between a choice of optional parameters.	Curly braces (`{' and
     `}') are used to group keywords and parameters when necessary.

Interface specification
     There are some statements that may or have to specify interface.  Inter‐
     faces are specified in the form of "name unit", such as lo0 and ep1.

Configuration Statements
     debug on|off;
	     Enables configuration file parser debugging.  If on is specified,
	     then debugging is enabled, If off is specified, then debugging is
	     disabled.	It is disabled by default.

     dest dest-list [retrycmd];
	     Specifies destinations to which router renumbering messages
	     should be sent.  dest-list can be any combination of single or
	     multiple numerical IPv6 addrs, or Full Qualified Domain Names.
	     retrycmd has following syntax.

	     retry retry-num
		     retry-num specifies how many router renumbering messages
		     are sent repeatedly.

     [add|change|setglobal]
	     match-prefix match-prefix-val [/match-prefix-len]
	     [maxlen maxlen-val] [minlen minlen-val]
	     [use-prefix use-prefix-val] [/use-prefix-len]
	     [keeplen keeplen-val] [use-prefix-values];

	     Specifies contents of sending router renumbering message with
	     seqnum 0.	If add|change|setglobal is not specified, then add is
	     assumed.  use-prefix-values has following syntax.

	     { [vltime vltime-val] [pltime pltime-val] [raf_onlink on|off]
	     [raf_auto on|off] [rrf_decrprefd on|off] [rrf_decrvalid on|off] }

	     Each value has following meaning.

	     match-prefix match-prefix-val [/match-prefix-len]
		     Specify match-prefix-val that is used for matching with
		     preassigned prefixes to which add|change|setglobal com‐
		     mand should be applied.  /match-prefix-len Specify the
		     starting part of match-prefix-val to be used for matching
		     with preassigned prefixes, as decimal bit number.
	     maxlen maxlen-val
		     Specify the maximum length of prefixes which is allowed
		     to be matched to match-prefix-val, as decimal bit number.
	     minlen minlen-val
		     Specify the minimum length of prefixes which is allowed
		     to be matched to match-prefix-val, as decimal bit number.
	     use-prefix use-prefix-val [/usr-prefix-len]
		     Specify use-prefix-val that is used for prefixes to be
		     added on add|change|setglobal command.  /use-prefix-len
		     Specify the starting part of use-prefix-val copied to the
		     starting part of prefixes to be added on
		     add|change|setglobal command, as decimal bit number.
	     keeplen keeplen-val
		     Specify the medium part of use-prefix-val just next to
		     the starting part specified by use-prefix-len, as decimal
		     bit number.  Contiguous bits part in the same bit posi‐
		     tion of an existent prefix matched with match-prefix-val
		     is copied to the same bit position of prefixes to be
		     added.
	     vltime vmtime-val
		     Assign an time as prefix valid life time for a prefix to
		     be added.	Valid value for time is decimal seconds number
		     or special format as "d00h00m00s00", where 00 can take
		     any decimal number, and "d" means days, "h" means hours,
		     "m" means minutes, "s" means seconds.  And alternatively,
		     special keyword "infinity" can be also be specified.
	     pltime pltime-val
		     Assign an time as prefix preferred life time for a prefix
		     to be added.  Valid value for time is same as for
		     vltime-val.
	     raf_onlink on|off
		     Let the prefix to be added to have on-link or off-link
		     nature for the assigned interface.	 If on is specified,
		     the prefix have on-link nature (e.g. the prefix belong to
		     the link).	 If off is specified, the prefix have off-link
		     nature (e.g. the prefix does not belong to the link).
	     raf_auto on|off
		     Enable or disable the autonomous address auto configura‐
		     tion for the prefix to be added.  If on is specified, au‐
		     tonomous address auto configuration is enabled.  If off
		     is specified, it is disabled.
	     rrf_decrprefd on|off
		     Enable or disable the decrementation of the pltime.  If
		     on is specified, decrementation of the pltime is enabled.
		     If off is specified, decrementation of the pltime is dis‐
		     abled.
	     rrf_decrvalid on|off
		     Enable or disable the decrementation of the vltime.  If
		     on is specified, decrementation of the vltime is enabled.
		     If off is specified, decrementation of the vltime is dis‐
		     abled.

     seqnum seqnum-val { rrenum-cmd };
	     Specifies contents of sending router renumbering message with
	     some specific seqnum.  Multiple of this statement can be speci‐
	     fied if they have different seqnum-val each other.	 rrenum-cmd
	     has just same syntax with above add|change|setglobal statement.

EXAMPLES
     For each configuration file example shown below, we suppose every IPv6
     subnet has its own prefix beginning with fec0:0:0::/48 and with its own
     subnet number (in this case, subnet number is 7th and 8th octet value of
     the prefix).

     If you want to assign prefixes beginning with 3ffe:501:ffff::/48 to each
     subnet, then following configuration will be enough, if each of your
     routers supports IPv6 multicast forwarding.  The subnet number of the
     existing fec0:0:0::/48 prefix and the newly assigned 3ffe:501:ffff::/48
     prefix will be same.

	   dest ff05::2;

	   add match-prefix fec0:0:0:: /48 use-prefix 3ffe:501:ffff:: /48 keeplen 16;

     If your routers do not support IPv6 multicast forwarding, you will need
     to specify each destination at dest command.

	   dest fec0:0:0:1:260:8ff:fe24:fb3a fec0:0:0:2:200:eff:fe2e:dfe1 fec0:0:0:3:5254:ff:fedc:5217;

	   add match-prefix fec0:0:0:: /48 use-prefix 3ffe:501:ffff:: /48 keeplen 16;

     If you are going to do renumbering, then following procedure will be nat‐
     ural.

	   1.	Assign a new prefix.

	   2.	Set old prefix lifetimes to some appropriate transition
		period.	 In the following example we use 1 week for valid
		lifetime, and 0 for preferred lifetime.	 Also, enable old pre‐
		fix lifetime expiration (By default, it is static and does not
		expire).

	   3.	After the transition period, old prefixes should become
		invalid, and may have been deleted.  To make sure that they
		are deleted, send new router renumbering message, which speci‐
		fies old prefixes as match prefix, and no use prefix.

     The following configuration file will do 1 and 2.

	   dest ff05::2;

	   seqnum 0 {
		   add match-prefix fec0:0:0:: /48 use-prefix 3ffe:501:fffe:: /48 keeplen 16;
		   };

	   seqnum 1 {
		   change match-prefix 3ffe:501:ffff:: /48 use-prefix 3ffe:501:ffff:: /48 keeplen 16 vltime d7 pltime 0 rrf_decrvalid on rrf_decrprefd on;
		   };

     And the following configuration file will do 3 (should be used for the
     router renumbering message to be sent 1 week afterward).

	   dest ff05::2;

	   change match-prefix 3ffe:501:ffff:: /48;

     In the above example, only add and change commands are used, and there is
     no example for setglobal command.	setglobal command is almost same with
     change command except that it deletes all pre-defined IPv6 global
     address.

SEE ALSO
     prefix(8), rrenumd(8)

HISTORY
     The rrenumd.conf configuration file was first appeared in KAME IPv6 pro‐
     tocol stack kit.

BSD			       November 5, 1998				   BSD
[top]

List of man pages available for FreeBSD

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net