SMARTD.CONF(5) 2013-04-20 SMARTD.CONF(5)NAMEsmartd.conf - SMART Disk Monitoring Daemon Configuration File
FULL PATH
/etc/smartd.conf
PACKAGE VERSION
smartmontools-6.2 2013-04-20 r3812
DESCRIPTION
[This man page is generated for the Linux version of smartmontools. It
does not contain info specific to other platforms.]
/etc/smartd.conf is the configuration file for the smartd daemon.
If the configuration file /etc/smartd.conf is present, smartd reads it
at startup, before fork(2)ing into the background. If smartd subse‐
quently receives a HUP signal, it will then re-read the configuration
file. If smartd is running in debug mode, then an INT signal will also
make it re-read the configuration file. This signal can be generated by
typing <CONTROL-C> in the terminal window where smartd is running.
In the absence of a configuration file smartd will try to open all
available devices (see smartd(8) man page). A configuration file with
a single line ´DEVICESCAN -a' would have the same effect.
This can be annoying if you have an ATA or SCSI device that hangs or
misbehaves when receiving SMART commands. Even if this causes no prob‐
lems, you may be annoyed by the string of error log messages about
devices that can´t be opened.
One can avoid this problem, and gain more control over the types of
events monitored by smartd, by using the configuration file
/etc/smartd.conf. This file contains a list of devices to monitor,
with one device per line. An example file is included with the smart‐
montools distribution. You will find this sample configuration file in
/usr/share/doc/smartmontools/. For security, the configuration file
should not be writable by anyone but root. The syntax of the file is as
follows:
· There should be one device listed per line, although you may have
lines that are entirely comments or white space.
· Any text following a hash sign ´#´ and up to the end of the line is
taken to be a comment, and ignored.
· Lines may be continued by using a backslash ´\´ as the last non-
whitespace or non-comment item on a line.
· Note: a line whose first character is a hash sign ´#´ is treated as
a white-space blank line, not as a non-existent line, and will end
a continuation line.
Here is an example configuration file. It´s for illustrative purposes
only; please don´t copy it onto your system without reading to the end
of the DIRECTIVES Section below!
################################################
# This is an example smartd startup config file
# /etc/smartd.conf for monitoring three
# ATA disks, three SCSI disks, six ATA disks
# behind two 3ware controllers, two disks on a cciss
# controller, three SATA disks directly connected
# to the HighPoint Rocket-RAID controller,
# two SATA disks connected to the HighPoint
# RocketRAID controller via a pmport
# device, four SATA disks connected to an Areca
# RAID controller, and one SATA disk.
#
# First ATA disk on two different interfaces. On
# the second disk, start a long self-test every
# Sunday between 3 and 4 am.
#
/dev/hda -a -m admin@example.com,root@localhost
/dev/hdc -a -I 194 -I 5 -i 12 -s L/../../7/03
#
# SCSI disks. Send a TEST warning email to admin on
# startup.
#
/dev/sda
/dev/sdb -m admin@example.com -M test
#
# Strange device. It´s SCSI. Start a scheduled
# long self test between 5 and 6 am Monday/Thursday
/dev/weird -d scsi -s L/../../(1|4)/05
#
# An ATA disk may appear as a SCSI device to the
# OS. If a SCSI to ATA Translation (SAT) layer
# is between the OS and the device then this can be
# flagged with the '-d sat' option. This situation
# may become common with SATA disks in SAS and FC
# environments.
/dev/sda -a -d sat
#
# Three disks connected to a MegaRAID controller
# Start short self-tests daily between 1-2, 2-3, and
# 3-4 am.
/dev/sda -d megaraid,0 -a -s S/../.././01
/dev/sda -d megaraid,1 -a -s S/../.././02
/dev/sda -d megaraid,2 -a -s S/../.././03
/dev/bus/0 -d megaraid,2 -a -s S/../.././03
#
# Four ATA disks on a 3ware 6/7/8000 controller.
# Start short self-tests daily between midnight and 1am,
# 1-2, 2-3, and 3-4 am. Starting with the Linux 2.6
# kernel series, /dev/sdX is deprecated in favor of
# /dev/tweN. For example replace /dev/sdc by /dev/twe0
# and /dev/sdd by /dev/twe1.
/dev/sdc -d 3ware,0 -a -s S/../.././00
/dev/sdc -d 3ware,1 -a -s S/../.././01
/dev/sdd -d 3ware,2 -a -s S/../.././02
/dev/sdd -d 3ware,3 -a -s S/../.././03
#
# Two ATA disks on a 3ware 9000 controller.
# Start long self-tests Sundays between midnight and
# 1am and 2-3 am
/dev/twa0 -d 3ware,0 -a -s L/../../7/00
/dev/twa0 -d 3ware,1 -a -s L/../../7/02
#
# Two SATA (not SAS) disks on a 3ware 9750 controller.
# Start long self-tests Sundays between midnight and
# 1am and 2-3 am
/dev/twl0 -d 3ware,0 -a -s L/../../7/00
/dev/twl0 -d 3ware,1 -a -s L/../../7/02
#
# Monitor 2 disks connected to the first HP SmartArray controller which
# uses the cciss driver. Start long tests on Sunday nights and short
# self-tests every night and send errors to root
/dev/cciss/c0d0 -d cciss,0 -a -s (L/../../7/02|S/../.././02) -m root
/dev/cciss/c0d0 -d cciss,1 -a -s (L/../../7/03|S/../.././03) -m root
#
# Three SATA disks on a HighPoint RocketRAID controller.
# Start short self-tests daily between 1-2, 2-3, and
# 3-4 am.
# under Linux
/dev/sde -d hpt,1/1 -a -s S/../.././01
/dev/sde -d hpt,1/2 -a -s S/../.././02
/dev/sde -d hpt,1/3 -a -s S/../.././03
#
# Two SATA disks connected to a HighPoint RocketRAID
# via a pmport device. Start long self-tests Sundays
# between midnight and 1am and 2-3 am.
# under Linux
/dev/sde -d hpt,1/4/1 -a -s L/../../7/00
/dev/sde -d hpt,1/4/2 -a -s L/../../7/02
# Three SATA disks connected to an Areca
# RAID controller. Start long self-tests Sundays
# between midnight and 3 am.
/dev/sg2 -d areca,1 -a -s L/../../7/00
/dev/sg2 -d areca,2 -a -s L/../../7/01
/dev/sg2 -d areca,3 -a -s L/../../7/02
#
# The following line enables monitoring of the
# ATA Error Log and the Self-Test Error Log.
# It also tracks changes in both Prefailure
# and Usage Attributes, apart from Attributes
# 9, 194, and 231, and shows continued lines:
#
/dev/hdd -l error \
-l selftest \
-t \ # Attributes not tracked:
-I 194 \ # temperature
-I 231 \ # also temperature
-I 9 # power-on hours
#
################################################
CONFIGURATION FILE DIRECTIVES
If a non-comment entry in the configuration file is the text string
DEVICESCAN in capital letters, then smartd will ignore any remaining
lines in the configuration file, and will scan for devices. DEVICESCAN
may optionally be followed by Directives that will apply to all devices
that are found in the scan. Please see below for additional details.
[NEW EXPERIMENTAL SMARTD FEATURE] If an entry in the configuration file
starts with DEFAULT instead of a device name, then all directives in
this entry are set as defaults for the next device entries.
This configuration:
DEFAULT -a -R5! -W 2,40,45 -I 194 -s L/../../7/00 -m admin@example.com
/dev/sda
/dev/sdb
/dev/sdc
DEFAULT -H -m admin@example.com
/dev/sdd
/dev/sde -d removable
has the same effect as:
/dev/sda -a -R5! -W 2,40,45 -I 194 -s L/../../7/00 -m admin@example.com
/dev/sdb -a -R5! -W 2,40,45 -I 194 -s L/../../7/00 -m admin@example.com
/dev/sdc -a -R5! -W 2,40,45 -I 194 -s L/../../7/00 -m admin@example.com
/dev/sdd -H -m admin@example.com
/dev/sde -d removable -H -m admin@example.com
The following are the Directives that may appear following the device
name or DEVICESCAN or DEFAULT on any line of the /etc/smartd.conf con‐
figuration file. Note that these are NOT command-line options for
smartd. The Directives below may appear in any order, following the
device name.
For an ATA device, if no Directives appear, then the device will be
monitored as if the ´-a´ Directive (monitor all SMART properties) had
been given.
If a SCSI disk is listed, it will be monitored at the maximum imple‐
mented level: roughly equivalent to using the ´-H -l selftest´ options
for an ATA disk. So with the exception of ´-d´, ´-m´, ´-l selftest´,
´-s´, and ´-M´, the Directives below are ignored for SCSI disks. For
SCSI disks, the ´-m´ Directive sends a warning email if the SMART sta‐
tus indicates a disk failure or problem, if the SCSI inquiry about disk
status fails, or if new errors appear in the self-test log.
If a 3ware controller is used then the corresponding SCSI (/dev/sd?) or
character device (/dev/twe?, /dev/twa?, /dev/twl? or /dev/tws?) must be
listed, along with the ´-d 3ware,N´ Directive (see below). The indi‐
vidual ATA disks hosted by the 3ware controller appear to smartd as
normal ATA devices. Hence all the ATA directives can be used for these
disks (but see note below).
If an Areca controller is used then the corresponding device (SCSI
/dev/sg? on Linux or /dev/arcmsr0 on FreeBSD) must be listed, along
with the ´-d areca,N´ Directive (see below). The individual SATA disks
hosted by the Areca controller appear to smartd as normal ATA devices.
Hence all the ATA directives can be used for these disks. Areca
firmware version 1.46 or later which supports smartmontools must be
used; Please see the smartctl(8) man page for further details.
-d TYPE
Specifies the type of the device. The valid arguments to this
directive are:
auto - attempt to guess the device type from the device name or
from controller type info provided by the operating system or
from a matching USB ID entry in the drive database. This is the
default.
ata - the device type is ATA. This prevents smartd from issuing
SCSI commands to an ATA device.
scsi - the device type is SCSI. This prevents smartd from issu‐
ing ATA commands to a SCSI device.
sat[,auto][,N] - the device type is SCSI to ATA Translation
(SAT). This is for ATA disks that have a SCSI to ATA Transla‐
tion (SAT) Layer (SATL) between the disk and the operating sys‐
tem. SAT defines two ATA PASS THROUGH SCSI commands, one 12
bytes long and the other 16 bytes long. The default is the 16
byte variant which can be overridden with either ´-d sat,12´ or
´-d sat,16´.
If ´-d sat,auto´ is specified, device type SAT (for ATA/SATA
disks) is only used if the SCSI INQUIRY data reports a SATL
(VENDOR: "ATA "). Otherwise device type SCSI (for SCSI/SAS
disks) is used.
usbcypress - this device type is for ATA disks that are behind a
Cypress USB to PATA bridge. This will use the ATACB proprietary
scsi pass through command. The default SCSI operation code is
0x24, but although it can be overridden with ´-d usbcy‐
press,0xN´, where N is the scsi operation code, you're running
the risk of damage to the device or filesystems on it.
usbjmicron[,p][,x][,PORT] - this device type is for SATA disks
that are behind a JMicron USB to PATA/SATA bridge. The 48-bit
ATA commands (required e.g. for ´-l xerror´, see below) do not
work with all of these bridges and are therefore disabled by
default. These commands can be enabled by ´-d usbjmicron,x´.
If two disks are connected to a bridge with two ports, an error
message is printed if no PORT is specified. The port can be
specified by ´-d usbjmicron[,x],PORT´ where PORT is 0 (master)
or 1 (slave). This is not necessary if the device uses a port
multiplier to connect multiple disks to one port. The disks
appear under separate /dev/ice names then. CAUTION: Specifying
´,x´ for a device which does not support it results in I/O
errors and may disconnect the drive. The same applies if the
specified PORT does not exist or is not connected to a disk.
[NEW EXPERIMENTAL SMARTD FEATURE] The Prolific PL2507/3507 USB
bridges with older firmware support a pass-through command simi‐
lar to JMicron and work with ´-d usbjmicron,0´. Newer Prolific
firmware requires a modified command which can be selected by
´-d usbjmicron,p´. Note that this does not yet support the
SMART status command.
usbsunplus - this device type is for SATA disks that are behind
a SunplusIT USB to SATA bridge.
marvell - [Linux only] interact with SATA disks behind Marvell
chip-set controllers (using the Marvell rather than libata
driver).
megaraid,N - [Linux only] the device consists of one or more
SCSI/SAS disks connected to a MegaRAID controller. The non-neg‐
ative integer N (in the range of 0 to 127 inclusive) denotes
which disk on the controller is monitored. This interface will
also work for Dell PERC controllers. In log files and email
messages this disk will be identified as megaraid_disk_XXX with
XXX in the range from 000 to 127 inclusive. It is possible to
set RAID device name as /dev/bus/N, where N is a SCSI bus num‐
ber. Please see the smartctl(8) man page for further details.
3ware,N - [FreeBSD and Linux only] the device consists of one or
more ATA disks connected to a 3ware RAID controller. The non-
negative integer N (in the range from 0 to 127 inclusive)
denotes which disk on the controller is monitored. In log files
and email messages this disk will be identified as
3ware_disk_XXX with XXX in the range from 000 to 127 inclusive.
Note that while you may use any of the 3ware SCSI logical
devices /dev/tw* to address any of the physical disks (3ware
ports), error and log messages will make the most sense if you
always list the 3ware SCSI logical device corresponding to the
particular physical disks. Please see the smartctl(8) man page
for further details.
areca,N - [FreeBSD, Linux, Windows and Cygwin only] the device
consists of one or more SATA disks connected to an Areca SATA
RAID controller. The positive integer N (in the range from 1 to
24 inclusive) denotes which disk on the controller is monitored.
In log files and email messages this disk will be identifed as
areca_disk_XX with XX in the range from 01 to 24 inclusive.
Please see the smartctl(8) man page for further details.
areca,N/E - [FreeBSD, Linux, Windows and Cygwin only] [NEW
EXPERIMENTAL SMARTD FEATURE] the device consists of one or more
SATA or SAS disks connected to an Areca SAS RAID controller.
The integer N (range 1 to 128) denotes the channel (slot) and E
(range 1 to 8) denotes the enclosure. Important: This requires
Areca SAS controller firmware version 1.51 or later.
cciss,N - [FreeBSD and Linux only] the device consists of one or
more SCSI/SAS or SATA disks connected to a cciss RAID con‐
troller. The non-negative integer N (in the range from 0 to 15
inclusive) denotes which disk on the controller is monitored.
In log files and email messages this disk will be identified as
cciss_disk_XX with XX in the range from 00 to 15 inclusive.
Please see the smartctl(8) man page for further details.
hpt,L/M/N - [FreeBSD and Linux only] the device consists of one
or more ATA disks connected to a HighPoint RocketRAID con‐
troller. The integer L is the controller id, the integer M is
the channel number, and the integer N is the PMPort number if it
is available. The allowed values of L are from 1 to 4 inclu‐
sive, M are from 1 to 16 inclusive and N from 1 to 4 if PMPort
available. And also these values are limited by the model of
the HighPoint RocketRAID controller. In log files and email
messages this disk will be identified as hpt_X/X/X and X/X/X is
the same as L/M/N, note if no N indicated, N set to the default
value 1. Please see the smartctl(8) man page for further
details.
ignore - [NEW EXPERIMENTAL SMARTD FEATURE] the device specified
by this configuration entry should be ignored. This allows to
ignore specific devices which are detected by a following
DEVICESCAN configuration line. It may also be used to temporary
disable longer multi-line configuration entries. This Directive
may be used in conjunction with the other ´-d´ Directives.
removable - the device or its media is removable. This indi‐
cates to smartd that it should continue (instead of exiting,
which is the default behavior) if the device does not appear to
be present when smartd is started. This Directive may be used
in conjunction with the other ´-d´ Directives.
-n POWERMODE[,N][,q]
[ATA only] This ´nocheck´ Directive is used to prevent a disk
from being spun-up when it is periodically polled by smartd.
ATA disks have five different power states. In order of increas‐
ing power consumption they are: ´OFF´, ´SLEEP´, ´STANDBY´,
´IDLE´, and ´ACTIVE´. Typically in the OFF, SLEEP, and STANDBY
modes the disk´s platters are not spinning. But usually, in
response to SMART commands issued by smartd, the disk platters
are spun up. So if this option is not used, then a disk which
is in a low-power mode may be spun up and put into a higher-
power mode when it is periodically polled by smartd.
Note that if the disk is in SLEEP mode when smartd is started,
then it won't respond to smartd commands, and so the disk won't
be registered as a device for smartd to monitor. If a disk is in
any other low-power mode, then the commands issued by smartd to
register the disk will probably cause it to spin-up.
The ´-n´ (nocheck) Directive specifies if smartd´s periodic
checks should still be carried out when the device is in a low-
power mode. It may be used to prevent a disk from being spun-up
by periodic smartd polling. The allowed values of POWERMODE
are:
never - smartd will poll (check) the device regardless of its
power mode. This may cause a disk which is spun-down to be spun-
up when smartd checks it. This is the default behavior if the
'-n' Directive is not given.
sleep - check the device unless it is in SLEEP mode.
standby - check the device unless it is in SLEEP or STANDBY
mode. In these modes most disks are not spinning, so if you
want to prevent a laptop disk from spinning up each time that
smartd polls, this is probably what you want.
idle - check the device unless it is in SLEEP, STANDBY or IDLE
mode. In the IDLE state, most disks are still spinning, so this
is probably not what you want.
Maximum number of skipped checks (in a row) can be specified by
appending positive number ´,N´ to POWERMODE (like ´-n
standby,15´). After N checks are skipped in a row, powermode is
ignored and the check is performed anyway.
When a periodic test is skipped, smartd normally writes an
informal log message. The message can be suppressed by appending
the option ´,q´ to POWERMODE (like ´-n standby,q´). This pre‐
vents a laptop disk from spinning up due to this message.
Both ´,N´ and ´,q´ can be specified together.
-T TYPE
Specifies how tolerant smartd should be of SMART command fail‐
ures. The valid arguments to this Directive are:
normal - do not try to monitor the disk if a mandatory SMART
command fails, but continue if an optional SMART command fails.
This is the default.
permissive - try to monitor the disk even if it appears to lack
SMART capabilities. This may be required for some old disks
(prior to ATA-3 revision 4) that implemented SMART before the
SMART standards were incorporated into the ATA/ATAPI Specifica‐
tions. [Please see the smartctl -T command-line option.]
-o VALUE
[ATA only] Enables or disables SMART Automatic Offline Testing
when smartd starts up and has no further effect. The valid
arguments to this Directive are on and off.
The delay between tests is vendor-specific, but is typically
four hours.
Note that SMART Automatic Offline Testing is not part of the ATA
Specification. Please see the smartctl -o command-line option
documentation for further information about this feature.
-S VALUE
Enables or disables Attribute Autosave when smartd starts up and
has no further effect. The valid arguments to this Directive
are on and off. Also affects SCSI devices. [Please see the
smartctl -S command-line option.]
-H [ATA only] Check the SMART health status of the disk. If any
Prefailure Attributes are less than or equal to their threshold
values, then disk failure is predicted in less than 24 hours,
and a message at loglevel ´LOG_CRIT´ will be logged to syslog.
[Please see the smartctl -H command-line option.]
-l TYPE
Reports increases in the number of errors in one of three SMART
logs. The valid arguments to this Directive are:
error - [ATA only] report if the number of ATA errors reported
in the Summary SMART error log has increased since the last
check.
xerror - [ATA only] report if the number of ATA errors reported
in the Extended Comprehensive SMART error log has increased
since the last check.
If both ´-l error´ and ´-l xerror´ are specified, smartd checks
the maximum of both values.
[Please see the smartctl -l xerror command-line option.]
selftest - report if the number of failed tests reported in the
SMART Self-Test Log has increased since the last check, or if
the timestamp associated with the most recent failed test has
increased. Note that such errors will only be logged if you run
self-tests on the disk (and it fails a test!). Self-Tests can
be run automatically by smartd: please see the ´-s´ Directive
below. Self-Tests can also be run manually by using the
´-t short´ and ´-t long´ options of smartctl and the results of
the testing can be observed using the smartctl ´-l selftest´
command-line option. [Please see the smartctl -l and -t com‐
mand-line options.]
[ATA only] Failed self-tests outdated by a newer successful
extended self-test are ignored. The warning email counter is
reset if the number of failed self tests dropped to 0. This
typically happens when an extended self-test is run after all
bad sectors have been reallocated.
offlinests[,ns] - [ATA only] report if the Offline Data Collec‐
tion status has changed since the last check. The report will
be logged as LOG_CRIT if the new status indicates an error.
With some drives the status often changes, therefore ´-l
offlinests´ is not enabled by '-a´ Directive. Appending ´,ns´
(no standby) to this directive is not implemented on Linux.
selfteststs[,ns] - [ATA only] report if the Self-Test execution
status has changed since the last check. The report will be
logged as LOG_CRIT if the new status indicates an error.
Appending ´,ns´ (no standby) to this directive is not imple‐
mented on Linux.
scterc,READTIME,WRITETIME - [ATA only] sets the SCT Error Recov‐
ery Control settings to the specified values (deciseconds) when
smartd starts up and has no further effect. Values of 0 disable
the feature, other values less than 65 are probably not sup‐
ported. For RAID configurations, this is typically set to 70,70
deciseconds. [Please see the smartctl -l scterc command-line
option.]
-e NAME[,VALUE]
Sets non-SMART device settings when smartd starts up and has no
further effect. [Please see the smartctl --set command-line
option.] Valid arguments are:
aam,[N|off] - [ATA only] Sets the Automatic Acoustic Management
(AAM) feature.
apm,[N|off] - [ATA only] Sets the Advanced Power Management
(APM) feature.
lookahead,[on|off] - [ATA only] Sets the read look-ahead fea‐
ture.
security-freeze - [ATA only] Sets ATA Security feature to frozen
mode.
standby,[N|off] - [ATA only] Sets the standby (spindown) timer
and places the drive in the IDLE mode.
wcache,[on|off] - [ATA only] Sets the volatile write cache fea‐
ture.
-s REGEXP
Run Self-Tests or Offline Immediate Tests, at scheduled times.
A Self- or Offline Immediate Test will be run at the end of
periodic device polling, if all 12 characters of the string
T/MM/DD/d/HH match the extended regular expression REGEXP. Here:
T is the type of the test. The values that smartd will try to
match (in turn) are: ´L´ for a Long Self-Test, ´S´ for a
Short Self-Test, ´C´ for a Conveyance Self-Test (ATA only),
and ´O´ for an Offline Immediate Test (ATA only). As soon
as a match is found, the test will be started and no addi‐
tional matches will be sought for that device and that
polling cycle.
To run scheduled Selective Self-Tests, use ´n´ for next
span, ´r´ to redo last span, or ´c´ to continue with next
span or redo last span based on status of last test. The
LBA range is based on the first span from the last test.
See the smartctl -t select,[next|redo|cont] options for fur‐
ther info.
Some disks (e.g. WD) do not preserve the selective self test
log accross power cycles. If state persistence (´-s´
option) is enabled, the last test span is preserved by
smartd and used if (and only if) the selective self test log
is empty.
MM is the month of the year, expressed with two decimal digits.
The range is from 01 (January) to 12 (December) inclusive.
Do not use a single decimal digit or the match will always
fail!
DD is the day of the month, expressed with two decimal digits.
The range is from 01 to 31 inclusive. Do not use a single
decimal digit or the match will always fail!
d is the day of the week, expressed with one decimal digit.
The range is from 1 (Monday) to 7 (Sunday) inclusive.
HH is the hour of the day, written with two decimal digits, and
given in hours after midnight. The range is 00 (midnight to
just before 1am) to 23 (11pm to just before midnight) inclu‐
sive. Do not use a single decimal digit or the match will
always fail!
Some examples follow. In reading these, keep in mind that in
extended regular expressions a dot ´.´ matches any single char‐
acter, and a parenthetical expression such as ´(A|B|C)´ denotes
any one of the three possibilities A, B, or C.
To schedule a short Self-Test between 2-3am every morning, use:
-s S/../.././02
To schedule a long Self-Test between 4-5am every Sunday morning,
use:
-s L/../../7/04
To schedule a long Self-Test between 10-11pm on the first and
fifteenth day of each month, use:
-s L/../(01|15)/./22
To schedule an Offline Immediate test after every midnight, 6am,
noon,and 6pm, plus a Short Self-Test daily at 1-2am and a Long
Self-Test every Saturday at 3-4am, use:
-s (O/../.././(00|06|12|18)|S/../.././01|L/../../6/03)
If Long Self-Tests of a large disks take longer than the system
uptime, a full disk test can be performed by several Selective
Self-Tests. To setup a full test of a 1TB disk within 20 days
(one 50GB span each day), run this command once:
smartctl -t select,0-99999999 /dev/sda
To run the next test spans on Monday-Friday between 12-13am, run
smartd with this directive:
-s n/../../[1-5]/12
Scheduled tests are run immediately following the regularly-
scheduled device polling, if the current local date, time, and
test type, match REGEXP. By default the regularly-scheduled
device polling occurs every thirty minutes after starting
smartd. Take caution if you use the ´-i´ option to make this
polling interval more than sixty minutes: the poll times may
fail to coincide with any of the testing times that you have
specified with REGEXP. In this case the test will be run fol‐
lowing the next device polling.
Before running an offline or self-test, smartd checks to be sure
that a self-test is not already running. If a self-test is
already running, then this running self test will not be inter‐
rupted to begin another test.
smartd will not attempt to run any type of test if another test
was already started or run in the same hour.
To avoid performance problems during system boot, smartd will
not attempt to run any scheduled tests following the very first
device polling (unless ´-q onecheck´ is specified).
Each time a test is run, smartd will log an entry to SYSLOG.
You can use these or the '-q showtests' command-line option to
verify that you constructed REGEXP correctly. The matching
order (L before S before C before O) ensures that if multiple
test types are all scheduled for the same hour, the longer test
type has precedence. This is usually the desired behavior.
If the scheduled tests are used in conjunction with state per‐
sistence (´-s´ option), smartd will also try to match the hours
since last shutdown (or 90 days at most). If any test would have
been started during downtime, the longest (see above) of these
tests is run after second device polling.
If the ´-n´ directive is used and any test would have been
started during disk standby time, the longest of these tests is
run when the disk is active again.
Unix users: please beware that the rules for extended regular
expressions [regex(7)] are not the same as the rules for file-
name pattern matching by the shell [glob(7)]. smartd will issue
harmless informational warning messages if it detects characters
in REGEXP that appear to indicate that you have made this mis‐
take.
-m ADD Send a warning email to the email address ADD if the ´-H´, ´-l´,
´-f´, ´-C´, or ´-O´ Directives detect a failure or a new error,
or if a SMART command to the disk fails. This Directive only
works in conjunction with these other Directives (or with the
equivalent default ´-a´ Directive).
To prevent your email in-box from getting filled up with warning
messages, by default only a single warning will be sent for each
of the enabled alert types, ´-H´, ´-l´, ´-f´, ´-C´, or ´-O´ even
if more than one failure or error is detected or if the failure
or error persists. [This behavior can be modified; see the ´-M´
Directive below.]
To send email to more than one user, please use the following
"comma separated" form for the address:
user1@add1,user2@add2,...,userN@addN (with no spaces).
To test that email is being sent correctly, use the ´-M test´
Directive described below to send one test email message on
smartd startup.
By default, email is sent using the system mail command. In
order that smartd find the mail command (normally /bin/mail) an
executable named ´mail´ must be in the path of the shell or
environment from which smartd was started. If you wish to spec‐
ify an explicit path to the mail executable (for example
/usr/local/bin/mail) or a custom script to run, please use the
´-M exec´ Directive below.
Note also that there is a special argument <nomailer> which can
be given to the ´-m´ Directive in conjunction with the ´-M exec´
Directive. Please see below for an explanation of its effect.
If the mailer or the shell running it produces any STDERR/STDOUT
output, then a snippet of that output will be copied to SYSLOG.
The remainder of the output is discarded. If problems are
encountered in sending mail, this should help you to understand
and fix them. If you have mail problems, we recommend running
smartd in debug mode with the ´-d´ flag, using the ´-M test´
Directive described below.
[NEW EXPERIMENTAL SMARTD FEATURE] If a word of the comma sepa‐
rated list has the form ´@plugin´, a custom script
/etc/smartd_warning.d/plugin is run and the word is removed from
the list before sending mail. The string ´plugin´ may be any
valid name except ´ALL´. If ´@ALL´ is specified, all scripts in
/etc/smartd_warning.d/* are run instead. This is handled by the
script /etc/smartd_warning.sh (see also ´-M exec´ below).
-M TYPE
These Directives modify the behavior of the smartd email warn‐
ings enabled with the ´-m´ email Directive described above.
These ´-M´ Directives only work in conjunction with the ´-m´
Directive and can not be used without it.
Multiple -M Directives may be given. If more than one of the
following three -M Directives are given (example: -M once -M
daily) then the final one (in the example, -M daily) is used.
The valid arguments to the -M Directive are (one of the follow‐
ing three):
once - send only one warning email for each type of disk problem
detected. This is the default unless state persistence (´-s´
option) is enabled.
daily - send additional warning reminder emails, once per day,
for each type of disk problem detected. This is the default if
state persistence (´-s´ option) is enabled.
diminishing - send additional warning reminder emails, after a
one-day interval, then a two-day interval, then a four-day
interval, and so on for each type of disk problem detected. Each
interval is twice as long as the previous interval.
If a disk problem is no longer detected, the internal email
counter is reset. If the problem reappears a new warning email
is sent immediately.
In addition, one may add zero or more of the following Direc‐
tives:
test - send a single test email immediately upon smartd startup.
This allows one to verify that email is delivered correctly.
Note that if this Directive is used, smartd will also send the
normal email warnings that were enabled with the ´-m´ Directive,
in addition to the single test email!
exec PATH - run the executable PATH instead of the default mail
command, when smartd needs to send email. PATH must point to an
executable binary file or script.
By setting PATH to point to a customized script, you can make
smartd perform useful tricks when a disk problem is detected
(beeping the console, shutting down the machine, broadcasting
warnings to all logged-in users, etc.) But please be careful.
smartd will block until the executable PATH returns, so if your
executable hangs, then smartd will also hang. Some sample
scripts are included in /usr/share/doc/smartmontools/examples//.
The return status of the executable is recorded by smartd in
SYSLOG. The executable is not expected to write to STDOUT or
STDERR. If it does, then this is interpreted as indicating that
something is going wrong with your executable, and a fragment of
this output is logged to SYSLOG to help you to understand the
problem. Normally, if you wish to leave some record behind, the
executable should send mail or write to a file or device.
Before running the executable, smartd sets a number of environ‐
ment variables. These environment variables may be used to con‐
trol the executable´s behavior. The environment variables
exported by smartd are:
SMARTD_MAILER
is set to the argument of -M exec, if present or else to
´mail´ (examples: /bin/mail, mail).
SMARTD_DEVICE
is set to the device path (examples: /dev/hda, /dev/sdb).
SMARTD_DEVICETYPE
is set to the device type specified by ´-d´ directive or
´auto´ if none.
SMARTD_DEVICESTRING
is set to the device description. For SMARTD_DEVICETYPE of
ata or scsi, this is the same as SMARTD_DEVICE. For 3ware
RAID controllers, the form used is ´/dev/sdc
[3ware_disk_01]´. For HighPoint RocketRAID controller, the
form is ´/dev/sdd [hpt_1/1/1]´ under Linux or ´/dev/hptrr
[hpt_1/1/1]´ under FreeBSD. For Areca controllers, the form
is ´/dev/sg2 [areca_disk_09]´ on Linux or ´/dev/arcmsr0
[areca_disk_09]´ on FreeBSD. In these cases the device
string contains a space and is NOT quoted. So to use
$SMARTD_DEVICESTRING in a bash script you should probably
enclose it in double quotes.
SMARTD_DEVICEINFO
is set to device identify information. It includes most of
the info printed by smartctl -i but uses a brief single line
format. This device info is also logged when smartd starts
up. The string contains space characters and is NOT quoted.
SMARTD_FAILTYPE
gives the reason for the warning or message email. The pos‐
sible values that it takes and their meanings are:
EmailTest: this is an email test message.
Health: the SMART health status indicates imminent failure.
Usage: a usage Attribute has failed.
SelfTest: the number of self-test failures has increased.
ErrorCount: the number of errors in the ATA error log has
increased.
CurrentPendingSector: one of more disk sectors could not be
read and are marked to be reallocated (replaced with spare
sectors).
OfflineUncorrectableSector: during off-line testing, or
self-testing, one or more disk sectors could not be read.
Temperature: Temperature reached critical limit (see -W
directive).
FailedHealthCheck: the SMART health status command failed.
FailedReadSmartData: the command to read SMART Attribute
data failed.
FailedReadSmartErrorLog: the command to read the SMART error
log failed.
FailedReadSmartSelfTestLog: the command to read the SMART
self-test log failed.
FailedOpenDevice: the open() command to the device failed.
SMARTD_ADDRESS
is determined by the address argument ADD of the ´-m´ Direc‐
tive. If ADD is <nomailer>, then SMARTD_ADDRESS is not set.
Otherwise, it is set to the comma-separated-list of email
addresses given by the argument ADD, with the commas
replaced by spaces (example:admin@example.com root). If
more than one email address is given, then this string will
contain space characters and is NOT quoted, so to use it in
a bash script you may want to enclose it in double quotes.
SMARTD_MESSAGE
is set to the one sentence summary warning email message
string from smartd. This message string contains space
characters and is NOT quoted. So to use $SMARTD_MESSAGE in a
bash script you should probably enclose it in double quotes.
SMARTD_FULLMESSAGE
is set to the contents of the entire email warning message
string from smartd. This message string contains space and
return characters and is NOT quoted. So to use
$SMARTD_FULLMESSAGE in a bash script you should probably
enclose it in double quotes.
SMARTD_TFIRST
is a text string giving the time and date at which the first
problem of this type was reported. This text string contains
space characters and no newlines, and is NOT quoted. For
example:
Sun Feb 9 14:58:19 2003 CST
SMARTD_TFIRSTEPOCH
is an integer, which is the unix epoch (number of seconds
since Jan 1, 1970) for SMARTD_TFIRST.
SMARTD_PREVCNT
is an integer specifying the number of previous messages
sent. It is set to ´0´ for the first message.
SMARTD_NEXTDAYS
is an integer specifying the number of days until the next
message will be sent. It it set to empty on ´-M once´ and
set to ´1´ on ´-M daily´.
The shell which is used to run PATH is system-dependent. For
vanilla Linux/glibc it´s bash. For other systems, the man page
for popen(3) should say what shell is used.
If the ´-m ADD´ Directive is given with a normal address argu‐
ment, then the executable pointed to by PATH will be run in a
shell with STDIN receiving the body of the email message, and
with the same command-line arguments:
-s "$SMARTD_SUBJECT" $SMARTD_ADDRESS
that would normally be provided to ´mail´. Examples include:
-m user@home -M exec /bin/mail
-m admin@work -M exec /usr/local/bin/mailto
-m root -M exec /Example_1/bash/script/below
If the ´-m ADD´ Directive is given with the special address
argument <nomailer> then the executable pointed to by PATH is
run in a shell with no STDIN and no command-line arguments, for
example:
-m <nomailer> -M exec /Example_2/bash/script/below
If the executable produces any STDERR/STDOUT output, then smartd
assumes that something is going wrong, and a snippet of that
output will be copied to SYSLOG. The remainder of the output is
then discarded.
Some EXAMPLES of scripts that can be used with the ´-M exec´
Directive are given below. Some sample scripts are also
included in /usr/share/doc/smartmontools/examples//.
[NEW EXPERIMENTAL SMARTD FEATURE] The executable is run by the
script /etc/smartd_warning.sh. This script formats subject and
full message based on SMARTD_MESSAGE and other environment vari‐
ables set by smartd. The environment variables SMARTD_SUBJECT
and SMARTD_FULLMESSAGE are set by the script before running the
executable.
-f [ATA only] Check for ´failure´ of any Usage Attributes. If
these Attributes are less than or equal to the threshold, it
does NOT indicate imminent disk failure. It "indicates an advi‐
sory condition where the usage or age of the device has exceeded
its intended design life period." [Please see the smartctl -A
command-line option.]
-p [ATA only] Report anytime that a Prefail Attribute has changed
its value since the last check. [Please see the smartctl -A com‐
mand-line option.]
-u [ATA only] Report anytime that a Usage Attribute has changed its
value since the last check. [Please see the smartctl -A command-
line option.]
-t [ATA only] Equivalent to turning on the two previous flags ´-p´
and ´-u´. Tracks changes in all device Attributes (both Pre‐
failure and Usage). [Please see the smartctl -A command-line
option.]
-i ID [ATA only] Ignore device Attribute number ID when checking for
failure of Usage Attributes. ID must be a decimal integer in
the range from 1 to 255. This Directive modifies the behavior
of the ´-f´ Directive and has no effect without it.
This is useful, for example, if you have a very old disk and
don´t want to keep getting messages about the hours-on-lifetime
Attribute (usually Attribute 9) failing. This Directive may
appear multiple times for a single device, if you want to ignore
multiple Attributes.
-I ID [ATA only] Ignore device Attribute ID when tracking changes in
the Attribute values. ID must be a decimal integer in the range
from 1 to 255. This Directive modifies the behavior of the
´-p´, ´-u´, and ´-t´ tracking Directives and has no effect with‐
out one of them.
This is useful, for example, if one of the device Attributes is
the disk temperature (usually Attribute 194 or 231). It´s annoy‐
ing to get reports each time the temperature changes. This
Directive may appear multiple times for a single device, if you
want to ignore multiple Attributes.
-r ID[!]
[ATA only] When tracking, report the Raw value of Attribute ID
along with its (normally reported) Normalized value. ID must be
a decimal integer in the range from 1 to 255. This Directive
modifies the behavior of the ´-p´, ´-u´, and ´-t´ tracking
Directives and has no effect without one of them. This Direc‐
tive may be given multiple times.
A common use of this Directive is to track the device Tempera‐
ture (often ID=194 or 231).
If the optional flag ´!´ is appended, a change of the Normalized
value is considered critical. The report will be logged as
LOG_CRIT and a warning email will be sent if ´-m´ is specified.
-R ID[!]
[ATA only] When tracking, report whenever the Raw value of
Attribute ID changes. (Normally smartd only tracks/reports
changes of the Normalized Attribute values.) ID must be a deci‐
mal integer in the range from 1 to 255. This Directive modifies
the behavior of the ´-p´, ´-u´, and ´-t´ tracking Directives and
has no effect without one of them. This Directive may be given
multiple times.
If this Directive is given, it automatically implies the ´-r´
Directive for the same Attribute, so that the Raw value of the
Attribute is reported.
A common use of this Directive is to track the device Tempera‐
ture (often ID=194 or 231). It is also useful for understanding
how different types of system behavior affects the values of
certain Attributes.
If the optional flag ´!´ is appended, a change of the Raw value
is considered critical. The report will be logged as LOG_CRIT
and a warning email will be sent if ´-m´ is specified. An exam‐
ple is ´-R 5!´ to warn when new sectors are reallocated.
-C ID[+]
[ATA only] Report if the current number of pending sectors is
non-zero. Here ID is the id number of the Attribute whose raw
value is the Current Pending Sector count. The allowed range of
ID is 0 to 255 inclusive. To turn off this reporting, use
ID = 0. If the -C ID option is not given, then it defaults to
-C 197 (since Attribute 197 is generally used to monitor pending
sectors). If the name of this Attribute is changed by a ´-v
197,FORMAT,NAME´ directive, the default is changed to -C 0.
If ´+´ is specified, a report is only printed if the number of
sectors has increased between two check cycles. Some disks do
not reset this attribute when a bad sector is reallocated. See
also ´-v 197,increasing´ below.
The warning email counter is reset if the number of pending sec‐
tors dropped to 0. This typically happens when all pending sec‐
tors have been reallocated or could be read again.
A pending sector is a disk sector (containing 512 bytes of your
data) which the device would like to mark as ``bad" and reallo‐
cate. Typically this is because your computer tried to read
that sector, and the read failed because the data on it has been
corrupted and has inconsistent Error Checking and Correction
(ECC) codes. This is important to know, because it means that
there is some unreadable data on the disk. The problem of fig‐
uring out what file this data belongs to is operating system and
file system specific. You can typically force the sector to
reallocate by writing to it (translation: make the device sub‐
stitute a spare good sector for the bad one) but at the price of
losing the 512 bytes of data stored there.
-U ID[+]
[ATA only] Report if the number of offline uncorrectable sectors
is non-zero. Here ID is the id number of the Attribute whose
raw value is the Offline Uncorrectable Sector count. The
allowed range of ID is 0 to 255 inclusive. To turn off this
reporting, use ID = 0. If the -U ID option is not given, then
it defaults to -U 198 (since Attribute 198 is generally used to
monitor offline uncorrectable sectors). If the name of this
Attribute is changed by a ´-v 198,FORMAT,NAME´ (except ´-v
198,FORMAT,Offline_Scan_UNC_SectCt´), directive, the default is
changed to -U 0.
If ´+´ is specified, a report is only printed if the number of
sectors has increased since the last check cycle. Some disks do
not reset this attribute when a bad sector is reallocated. See
also ´-v 198,increasing´ below.
The warning email counter is reset if the number of offline
uncorrectable sectors dropped to 0. This typically happens when
all offline uncorrectable sectors have been reallocated or could
be read again.
An offline uncorrectable sector is a disk sector which was not
readable during an off-line scan or a self-test. This is impor‐
tant to know, because if you have data stored in this disk sec‐
tor, and you need to read it, the read will fail. Please see
the previous ´-C´ option for more details.
-W DIFF[,INFO[,CRIT]]
Report if the current temperature had changed by at least DIFF
degrees since last report, or if new min or max temperature is
detected. Report or Warn if the temperature is greater or equal
than one of INFO or CRIT degrees Celsius. If the limit CRIT is
reached, a message with loglevel ´LOG_CRIT´ will be logged to
syslog and a warning email will be send if ´-m´ is specified. If
only the limit INFO is reached, a message with loglevel
´LOG_INFO´ will be logged.
The warning email counter is reset if the temperature dropped
below INFO or CRIT-5 if INFO is not specified.
If this directive is used in conjunction with state persistence
(´-s´ option), the min and max temperature values are preserved
across boot cycles. The minimum temperature value is not updated
during the first 30 minutes after startup.
To disable any of the 3 reports, set the corresponding limit to
0. Trailing zero arguments may be omitted. By default, all tem‐
perature reports are disabled (´-W 0´).
To track temperature changes of at least 2 degrees, use:
-W 2
To log informal messages on temperatures of at least 40 degrees,
use:
-W 0,40
For warning messages/mails on temperatures of at least 45
degrees, use:
-W 0,0,45
To combine all of the above reports, use:
-W 2,40,45
For ATA devices, smartd interprets Attribute 194 or 190 as Tem‐
perature Celsius by default. This can be changed to Attribute 9
or 220 by the drive database or by the ´-v 9,temp´ or ´-v
220,temp´ directive.
-F TYPE
[ATA only] Modifies the behavior of smartd to compensate for
some known and understood device firmware bug. This directive
may be used multiple times. The valid arguments are:
none - Assume that the device firmware obeys the ATA specifica‐
tions. This is the default, unless the device has presets for
´-F´ in the drive database. Using this directive will over-ride
any preset values.
nologdir - Suppresses read attempts of SMART or GP Log Direc‐
tory. Support for all standard logs is assumed without an
actual check. Some Intel SSDs may freeze if log address 0 is
read.
samsung - In some Samsung disks (example: model SV4012H Firmware
Version: RM100-08) some of the two- and four-byte quantities in
the SMART data structures are byte-swapped (relative to the ATA
specification). Enabling this option tells smartd to evaluate
these quantities in byte-reversed order. Some signs that your
disk needs this option are (1) no self-test log printed, even
though you have run self-tests; (2) very large numbers of ATA
errors reported in the ATA error log; (3) strange and impossible
values for the ATA error log timestamps.
samsung2 - In some Samsung disks the number of ATA errors
reported is byte swapped. Enabling this option tells smartd to
evaluate this quantity in byte-reversed order.
samsung3 - Some Samsung disks (at least SP2514N with Firmware
VF100-37) report a self-test still in progress with 0% remaining
when the test was already completed. If this directive is speci‐
fied, smartd will not skip the next scheduled self-test (see
Directive ´-s´ above) in this case.
xerrorlba - This only affects smartctl.
[Please see the smartctl -F command-line option.]
-v ID,FORMAT[:BYTEORDER][,NAME]
[ATA only] Sets a vendor-specific raw value print FORMAT, an
optional BYTEORDER and an optional NAME for Attribute ID. This
directive may be used multiple times. Please see smartctl -v
command-line option for further details.
The following arguments affect smartd warning output:
197,increasing - Raw Attribute number 197 (Current Pending Sec‐
tor Count) is not reset if uncorrectable sectors are reallo‐
cated. This sets ´-C 197+´ if no other ´-C´ directive is speci‐
fied.
198,increasing - Raw Attribute number 198 (Offline Uncorrectable
Sector Count) is not reset if uncorrectable sector are reallo‐
cated. This sets ´-U 198+´ if no other ´-U´ directive is speci‐
fied.
-P TYPE
[ATA only] Specifies whether smartd should use any preset
options that are available for this drive. The valid arguments
to this Directive are:
use - use any presets that are available for this drive. This
is the default.
ignore - do not use any presets for this drive.
show - show the presets listed for this drive in the database.
showall - show the presets that are available for all drives and
then exit.
[Please see the smartctl -P command-line option.]
-a Equivalent to turning on all of the following Directives: ´-H´
to check the SMART health status, ´-f´ to report failures of
Usage (rather than Prefail) Attributes, ´-t´ to track changes in
both Prefailure and Usage Attributes, ´-l error´ to report
increases in the number of ATA errors, ´-l selftest´ to report
increases in the number of Self-Test Log errors, ´-l selftest‐
sts´ to report changes of Self-Test execution status, ´-C 197´
to report nonzero values of the current pending sector count,
and ´-U 198´ to report nonzero values of the offline pending
sector count.
Note that -a is the default for ATA devices. If none of these
other Directives is given, then -a is assumed.
# Comment: ignore the remainder of the line.
\ Continuation character: if this is the last non-white or non-
comment character on a line, then the following line is a con‐
tinuation of the current one.
If you are not sure which Directives to use, I suggest experimenting
for a few minutes with smartctl to see what SMART functionality your
disk(s)support(s). If you do not like voluminous syslog messages, a
good choice of smartd configuration file Directives might be:
-H -l selftest -l error -f.
If you want more frequent information, use: -a.
If a cciss controller is used then the corresponding block device
(/dev/cciss/c?d?) must be listed, along with the ´-d cciss,N´ Directive
(see below).
ADDITIONAL DETAILS ABOUT DEVICESCAN
If a non-comment entry in the configuration file is the text
string DEVICESCAN in capital letters, then smartd will ignore
any remaining lines in the configuration file, and will scan for
devices (see also smartd(8) man page).
If DEVICESCAN is not followed by any Directives, then smartd
will scan for both ATA and SCSI devices, and will monitor all
possible SMART properties of any devices that are found.
DEVICESCAN may optionally be followed by any valid Directives,
which will be applied to all devices that are found in the scan.
For example
DEVICESCAN -m root@example.com
will scan for all devices, and then monitor them. It will send
one email warning per device for any problems that are found.
DEVICESCAN -d ata -m root@example.com
will do the same, but restricts the scan to ATA devices only.
DEVICESCAN -H -d ata -m root@example.com
will do the same, but only monitors the SMART health status of
the devices, (rather than the default -a, which monitors all
SMART properties).
[NEW EXPERIMENTAL SMARTD FEATURE] Configuration entries for spe‐
cific devices may precede the DEVICESCAN entry. For example
DEFAULT -m root@example.com
/dev/sda -s S/../.././02
/dev/sdc -d ignore
DEVICESCAN -s L/../.././02
will scan for all devices except /dev/sda and /dev/sdc, monitor
them, and run a long test between 2-3am every morning. Device
/dev/sda will also be monitored, but only a short test will be
run. Device /dev/sdc will be ignored. Warning emails will be
sent for all monitored devices.
EXAMPLES OF SHELL SCRIPTS FOR ´-M exec´
These are two examples of shell scripts that can be used with
the ´-M exec PATH´ Directive described previously. The paths to
these scripts and similar executables is the PATH argument to
the ´-M exec PATH´ Directive.
Example 1: This script is for use with ´-m ADDRESS -M exec
PATH´. It appends the output of smartctl -a to the output of
the smartd email warning message and sends it to ADDRESS.
#! /bin/bash
# Save the email message (STDIN) to a file:
cat > /root/msg
# Append the output of smartctl -a to the message:
/usr/sbin/smartctl -a -d $SMART_DEVICETYPE $SMARTD_DEVICE >> /root/msg
# Now email the message to the user at address ADD:
/bin/mail -s "$SMARTD_SUBJECT" $SMARTD_ADDRESS < /root/msg
Example 2: This script is for use with ´-m <nomailer> -M exec
PATH´. It warns all users about a disk problem, waits 30 sec‐
onds, and then powers down the machine.
#! /bin/bash
# Warn all users of a problem
wall ´Problem detected with disk: ´ "$SMARTD_DEVICESTRING"
wall ´Warning message from smartd is: ´ "$SMARTD_MESSAGE"
wall ´Shutting down machine in 30 seconds... ´
# Wait half a minute
sleep 30
# Power down the machine
/sbin/shutdown -hf now
Some example scripts are distributed with the smartmontools
package, in /usr/share/doc/smartmontools/examples/.
Please note that these scripts typically run as root, so any
files that they read/write should not be writable by ordinary
users or reside in directories like /tmp that are writable by
ordinary users and may expose your system to symlink attacks.
As previously described, if the scripts write to STDOUT or
STDERR, this is interpreted as indicating that there was an
internal error within the script, and a snippet of STDOUT/STDERR
is logged to SYSLOG. The remainder is flushed.
AUTHORS
Bruce Allen
University of Wisconsin - Milwaukee Physics Department
Christian Franke (Windows interface, C++ redesign, most enhancements
since 2009)
smartmontools-support@lists.sourceforge.net
CONTRIBUTORS
The following have made large contributions to smartmontools:
Casper Dik (Solaris SCSI interface)
Douglas Gilbert (SCSI subsystem)
Guido Guenther (Autoconf/Automake packaging)
Geoffrey Keating (Darwin ATA interface)
Eduard Martinescu (FreeBSD interface)
Frédéric L. W. Meunier (Web site and Mailing list)
Gabriele Pohl (Web site and Wiki, conversion from CVS to SVN)
Keiji Sawada (Solaris ATA interface)
Manfred Schwarb (Drive database)
Sergey Svishchev (NetBSD interface)
David Snyder and Sergey Svishchev (OpenBSD interface)
Phil Williams (User interface and drive database)
Shengfeng Zhou (Linux/FreeBSD HighPoint RocketRAID interface)
Many other individuals have made smaller contributions and corrections.
CREDITS
This code was derived from the smartsuite package, written by Michael
Cornwell, and from the previous UCSC smartsuite package. It extends
these to cover ATA-5 disks. This code was originally developed as a
Senior Thesis by Michael Cornwell at the Concurrent Systems Laboratory
(now part of the Storage Systems Research Center), Jack Baskin School
of Engineering, University of California, Santa Cruz.
http://ssrc.soe.ucsc.edu/ .
HOME PAGE FOR SMARTMONTOOLS:
Please see the following web site for updates, further documentation,
bug reports and patches: http://smartmontools.sourceforge.net/
SEE ALSO:smartd(8), smartctl(8), syslogd(8), syslog.conf(5), badblocks(8),
ide-smart(8), regex(7).
SVN ID OF THIS PAGE:
$Id: smartd.conf.5.in 3741 2013-01-02 17:06:54Z chrfranke $
smartmontools-6.2 2013-04-20 SMARTD.CONF(5)
