ptosm(7)


ptosm -- I2O pass-through OSM

Description

ptosm is a character special device which allows low-level access to the I2O subsystem from user space. The I2O subsystem is configured via HTML using a standard browser such as Netscape Navigator(TM). The I2O-dialog daemon which interfaces the browser to the I2O subsystem is the primary user of the ptosm device. The device driver is implemented as a loadable STREAMS driver.

ioctl commands

The ptosm device supports two ioctl(2) commands:

I2O_PT_NUMIOPS
This command obtains the number of I/O processors (IOPs).
#include <sys/i2o/ptosm.h>

int fd, stat, num;

stat = ioctl(fd, I2O_PT_NUMIOPS, &num);

If the ioctl returns success then num contains the number of IOPs registered in the I2O message layer.

I2O_PT_MSGTFR
This command transfers messages to or from an IOP.
#include <sys/i2o/ptosm.h>

int fd, stat; I2OptUserMsg_t i2oUserMsg;

stat = ioctl(fd, I2O_PT_MSGTFR, &i2oUserMsg);

I2OptUserMsg_t is a typedef of the following structure:
typedef struct {
        unsigned char   Version;
        unsigned char   IopNum;
        unsigned char   Pad[2];
        void            *Message;
        unsigned int    MessageLength;
        void            *Reply;
        unsigned int    ReplyLength;
        I2OPtData       Data[MAX_PT_SGL_BUFFERS];
} I2OptUserMsg_t;
Version should be set to I2O_CURRENT_VERSION.

IopNum should be set to the number of the desired target IOP.

Message is a pointer to a buffer containing a copy of the I2O message that is to be sent to the IOP. MessageLength is the length of this buffer.

The ptosm driver will generate and fill in the SGLOffset, MessageFlags and MessageLength fields of an I2O message. It will also generate the scatter/gather lists (SGLs) from information in the Data[] entries.


NOTE: The InitiatorContext and TransactionContext fields will be used for ptosm private data and will not be preserved in the Reply buffer.

Reply is a pointer to a buffer where the ptosm will place the reply from the IOP.

ReplyLength is the size of the Reply buffer. The ptosm will copy data up to this from the actual reply.


NOTE: It is an error for the Reply buffer to be smaller than a standard I2O reply message.

Data[] is an array of I2OPtData structures:

typedef struct {
        void            *Data;
        unsigned int    Length;
        unsigned int    Flags;
} I2OPtData;
Data is a pointer to a buffer that contains data to be written to the IOP or will contain data read from the IOP.

Length is the length of the buffer in bytes.

Flags controls the direction of data movement and is one of I2O_PT_DATA_READ or I2O_PT_DATA_WRITE. All other fields are reserved for future use and must be set to zero.

For each Data[] element that has the Flags field set to I2O_PT_DATA_READ or I2O_PT_DATA_WRITE, the ptosm driver creates a scatter/gather list (SGL) entry on the end of the Message that it sends to the IOP. Data array elements must be filled in, in order, from element 0.

Diagnostics

ioctl sets the following values in errno on failure:

EINVAL
A parameter error. This may include:

ENOMEM
The system failed to allocate an internal buffer or could not get a valid message frame from the target IOP.


NOTE: The ioctl will only return a failure if it could not deliver the message to the IOP. Failure messages from the IOP do not represent an ioctl failure and hence will return SUCCESS. In such cases, the Reply buffer will contain the response from the IOP. The InitiatorContext and TransactionContext fields will only contain data that is valid to the ptosm, any user data placed in these fields in the Message will have been overwritten. If the Response indicates an I2O transport failure with a PreservedMfa attached, then the ptosm will already have dealt with this.

Warnings

This ioctl allows the user to send nearly all messages to the IOP. Sending messages that modify the behavior or running state of an IOP or any of its software could seriously impact system performance and may lead to a system panic, data loss, or both.

Notices

In the current version of the interface (I2O_PT_VERSION_1) there may be a maximum of 4 SGLs attached to the message. Each dynamically created SGL will be of type SIMPLE. All messages must be of a type that generate a SINGLE_REPLY frame.
© 2004 The SCO Group, Inc. All rights reserved.
UnixWare 7 Release 7.1.4 - 25 April 2004