Contents


 1. Using LMTP over UNIX Socket

 2. Using LMTP over TCP Socket

 3. Verifying recipients using LMTP

 4. Delivering mails case insensitively

Exim provides support for LMTP over UNIX sockets using the LMTP transport
[http://www.exim.org/exim-html-current/doc/html/spec_html/ch-the_lmtp_transport.html],
your distribution may/not provide this, run exim -bV and check for 'lmtp' in
'Transports:'. Support for LMTP over TCP sockets is provided by the SMTP
transport
[http://www.exim.org/exim-html-current/doc/html/spec_html/ch-the_smtp_transport.html].

Using LMTP over UNIX Socket
---------------------------

Use this configuration if dovecot runs on the same host as exim.

Example router:

---%<-------------------------------------------------------------------------
local_user:
        debug_print = "R: local_user for $local_part@$domain"
        driver = accept
        domains = +local_domains
        check_local_user
        transport = dovecot_lmtp
        cannot_route_message = Unknown user
---%<-------------------------------------------------------------------------

Example transport:

---%<-------------------------------------------------------------------------
dovecot_lmtp:
        driver = lmtp
        socket = /var/run/dovecot/lmtp
        #maximum number of deliveries per batch, default 1
        batch_max = 200
---%<-------------------------------------------------------------------------

Using LMTP over TCP Socket
--------------------------

Example router:

---%<-------------------------------------------------------------------------
local_user:
        transport = dovecot_lmtp
        domains = +local_domains
        driver = manualroute
        route_list = "* 192.168.1.0 byname"
        #if destination server is the local host enable this
        #self = send
---%<-------------------------------------------------------------------------

Set IP and port as appropriate to your setup.

Example transport:

---%<-------------------------------------------------------------------------
dovecot_lmtp:
        driver = smtp
        protocol = lmtp
        port = 2525
---%<-------------------------------------------------------------------------

Verifying recipients using LMTP
-------------------------------

You can use callout verification to avoid accepting mail for addresses which do
not exist in Dovecot. Below is a config snippet which could be used in
acl_smtp_rcpt to achieve this:

---%<-------------------------------------------------------------------------
deny
        message = invalid recipient
        domains = +local_domains
        !verify = recipient/callout=no_cache
---%<-------------------------------------------------------------------------

For more information on address verification see the related section of the
Exim specification
[http://www.exim.org/exim-html-current/doc/html/spec_html/ch-access_control_lists.html#SECTaddressverification].

Delivering mails case insensitively
-----------------------------------

*Warning: *Just use this setup if all your login names contain only lower case
characters! (On Linux see /etc/adduser.conf under NAME_REGEX variable).

Exim retains the case of the local part. Dovecot's LMTP /may/ fail looking up
an incorrect cased local part in your userdb. You can solve this problem by
extending the /protocol lmtp/ section:

---%<-------------------------------------------------------------------------
protocol lmtp {
   ...
   # use %Ln to strip away the domain part
   auth_username_format = %Lu
}
---%<-------------------------------------------------------------------------

(If you don't mind allowing case insensitive logins for dovecoth
authentication, you may set /auth_username_format/ in the global configuration
accordingly and renounce the above change).

In case you prefer to configure exim to lower case the local part instead, add
a router just before your local delivery router:

---%<-------------------------------------------------------------------------
lowercase_local:
        debug_print = "R: lower case local_part for local delivery"
        driver = redirect
        redirect_router = local_user
        data = ${lc:${local_part}}
---%<-------------------------------------------------------------------------

Make sure to reference the name you have chosen for your local delivery router
within /redirect_router/.

(This file was created from the wiki on 2014-10-03 04:43)