btpd man page on DragonFly

Printed from http://www.polarhome.com/service/man/?qf=btpd&af=0&tf=2&of=DragonFly

BTPD(1)				 User Commands			       BTPD(1)

NAME
       btpd - BitTorrent Protocol Daemon

SYNOPSIS
       btpd [-d dir] [-p port] [OPTIONS...]

DESCRIPTION
       Btpd is a utility for sharing files over the BitTorrent network
       protocol.  It runs in daemon mode, thus needing no controlling terminal
       or gui.	Instead, the daemon is controlled by btcli, its control
       utility, or other programs capable of sending commands and queries on
       the control socket.

       btpd consists of the following programs:
	   btpd - The bittorrent client.
	   btcli - Command line interface to btpd.
	   btinfo - Shows information from a torrent file.

       All programs accept the --help option.

OPTIONS
       -d dir The path for the btpd directory.	Default is $HOME/.btpd.

       -p n, --port n
	      Listen at port n. Default is 6881.

       --help [mode]
	      Show this text or help for the specified mode.

       -4     Use IPv4. If given in conjunction with -6, both versions are
	      used.

       -6     Use IPv6. By default IPv4 is used.  Unfortunately enabling both
	      IPv6 and IPv4 in btpd is less useful than it should be. The
	      problem is that some sites have trackers for both versions and
	      it's likely that the IPv6 one, which probably has less peers,
	      will be used in favour of the IPv4 one.

       --bw-in n
	      Limit incoming BitTorrent traffic to n kB/s.  Default is 0 which
	      means unlimited.

       --bw-out n
	      Limit outgoing BitTorrent traffic to n kB/s.  Default is 0 which
	      means unlimited.

       --empty-start
	      Start btpd without any active torrents.

       --ip addr
	      Let the tracker distribute the given address instead of the one
	      it sees btpd connect from.

       --ipcprot mode
	      Set the protection mode of the command socket.  The mode is
	      specified by an octal number. Default is 0600.

       --logfile file
	      Where to put the logfile. By default it's put in the btpd dir.

       --max-peers n
	      Limit the amount of peers to n.

       --max-uploads n
	      Controls the number of simultaneous uploads.  The possible
	      values are:
	      n < -1 : Choose n >= 2 based on --bw-out (default).
	      n = -1 : Upload to every interested peer.
	      n =  0 : Dont't upload to anyone.
	      n >  0 : Upload to at most n peers simultaneously.

       --no-daemon
	      Keep the btpd process in the foregorund and log to std{out,err}.
	      This option is intended for debugging purposes.

       --prealloc n
	      Preallocate disk space in chunks of n kB. Default is 2048.  Note
	      that n will be rounded up to the closest multiple of the torrent
	      piece size. If n is zero no preallocation will be done.

STARTING BTPD
       To start btpd with default settings you only need to run it. However,
       there are many useful options you may want to use. To see a full list
       run btpd --help. If you didn't specify otherwise,  btpd starts with the
       same set of active torrents as it had the last time it was shut down.

       btdp will store information and write its log in $HOME/.btpd. Therefore
       it needs to be able to write there during its execution. You can
       specify another directory via the -d option or the $BTPD_HOME variable.

       It is recommended to specifiy the maximum number of uploads. Bittorrent
       employs a tit for tat algorithm, so uploading at good rates allows for
       downloading.  Try to find a balance between uploads/outgoing bandwidth
       and the number of active torrents.

       Note: You should only need one instance of btpd regardless of how many
       torrents you want to share.

EXAMPLES
       Start btpd with all options set to their default values.
	   $ btpd

       Start btpd as above, but with torrent data in the directory
       /var/torrents
	   $ btpd -d /var/torrents

       Start btpd and make it listen on port 12345, limit outgoing bandwidth
       to 200kB/s, limit the number of peers to 40 and not start any torrents
       that were active the last time btpd was shut down.
	   $ btpd -p 12345 --bw-out 200 --max-peers 40 --empty-start

TROUBLESHOOTING
       If btpd has shut down for some unknown reason, check the logfile for
       possible clues.

BUGS
       Known bugs are listed at http://github.com/queueRAM/btpd/issues

       Before submitting a bug report, please verify that you are running the
       latest version of btpd.

AUTHORS
       Current maintainers:

       - Marq Schneider <queueRAM@gmail.com>

       Past contributors:

       - Richard Nyberg <btpd@murmeldjur.se>

SEE ALSO
       btcli(1) btinfo(1)

BitTorrent Protocol Daemon 0.16	  2010-07-31			       BTPD(1)
[top]

List of man pages available for DragonFly

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net