RAW2TIFF(1)RAW2TIFF(1)NAMEraw2tiff - create a TIFF file from a raw data
SYNOPSISraw2tiff [ options ] input.raw output.tif
DESCRIPTIONraw2tiff converts a raw byte sequence into TIFF. By default, the TIFF
image is created with data samples packed (PlanarConfiguration=1), com‐
pressed with the PackBits algorithm (Compression=32773), and with each
strip no more than 8 kilobytes. These characteristics can overridden,
or explicitly specified with the options described below.
size of input image file header in bytes (0 by default). This
amount of data just will be skipped from the start of file while
width of input image in pixels (can be guessed, see GUESSING THE
IMAGE GEOMETRY below).
length of input image in lines (can be guessed, see GUESSING THE
IMAGE GEOMETRY below).
number of bands in input image (1 by default).
type of samples in input image, where data_type may be:
byte 8-bit unsigned integer (default),
short 16-bit unsigned integer,
long 32-bit unsigned integer,
sbyte 8-bit signed integer,
sshort 16-bit signed integer,
slong 32-bit signed integer,
float 32-bit IEEE floating point,
double 64-bit IEEE floating point.
type of samples interleaving in input image, where config may
pixel pixel interleaved data (default),
band band interleaved data.
photometric interpretation (color space) of the input image,
where photo may be:
miniswhite white color represented with 0 value,
minisblack black color represented with 0 value (default),
rgb image has RGB color model,
cmyk image has CMYK (separated) color model,
ycbcr image has YCbCr color model,
cielab image has CIE L*a*b color model,
icclab image has ICC L*a*b color model,
itulab image has ITU L*a*b color model.
-s swap bytes fetched from the input file.
-L input data has LSB2MSB bit order (default).
-M input data has MSB2LSB bit order.
-c Specify a compression scheme to use when writing image data: -c
none for no compression, -c packbits for the PackBits compres‐
sion algorithm (the default), -c jpeg for the baseline JPEG com‐
pression algorithm, -c zip for the Deflate compression algo‐
rithm, and -c lzw for Lempel-Ziv & Welch.
Write data with a specified number of rows per strip; by default
the number of rows/strip is selected so that each strip is
approximately 8 kilobytes.
GUESSING THE IMAGE GEOMETRYraw2tiff can guess image width and height in case one or both of these
parameters are not specified. If you omit one of those parameters, the
complementary one will be calculated based on the file size (taking
into account header size, number of bands and data type). If you omit
both parameters, the statistical approach will be used. Utility will
compute correlation coefficient between two lines at the image center
using several appropriate line sizes and the highest absolute value of
the coefficient will indicate the right line size. That is why you
should be cautious with the very large images, because guessing process
may take a while (depending on your system performance). Of course, the
utility can't guess the header size, number of bands and data type, so
it should be specified manually. If you don't know anything about your
image, just try with the several combinations of those options.
There is no magic, it is just a mathematical statistics, so it can be
wrong in some cases. But for most ordinary images guessing method will
SEE ALSOpal2rgb(1), tiffinfo(1), tiffcp(1), tiffmedian(1), libtiff(3)
Libtiff library home page: http://www.remotesensing.org/libtiff/
libtiff November 2, 2005 RAW2TIFF(1)