sg_reassign man page on Scientific
[printable version]
SG_REASSIGN(8) SG3_UTILS SG_REASSIGN(8)
NAME
sg_reassign - sends a SCSI REASSIGN BLOCKS command
SYNOPSIS
sg_reassign [--address=A,A...] [--dummy] [--eight=0|1] [--grown]
[--help] [--longlist=0|1] [--primary] [--verbose] [--version] DEVICE
DESCRIPTION
Send a SCSI REASSIGN BLOCKS command to DEVICE. Alternatively this util‐
ity can find the number of element in a "grown" or "primary" defect
list with a SCSI READ DEFECT DATA (10) command. These SCSI commands are
defined in SBC-2 for direct access devices (e.g. a disk). Reassign
blocks is designed to change the physical location of a logical block
that is known or suspected to be defective to another area on the
media. Disks are typically formatted with blocks held in reserve for
this situation.
If neither the --grown nor --primary option is supplied then one or
more addresses need to be given. If the address (or all of the
addresses) fit into 4 bytes and '--eight=1' is not given then the
parameter block passed to DEVICE is made up of 4 byte logical block
addresses. If any of the addresses need more than 4 bytes to represent
(i.e. >= 2**32) or '--eight=1' is given then the parameter block passed
to DEVICE is made up of 8 byte logical block addresses.
OPTIONS
Arguments to long options are mandatory for short options as well.
-a, --address=A,A...
where A,A... is a string of comma separated numbers. Each number
is interpreted as decimal unless prefixed by '0x' or '0X' (or it
has a trailing 'h' or 'H'). If multiple logical block addresses
are given they must be separated by a comma or a (single) space.
A string that contains any space separators needs to be quoted.
At least one address must be given.
-a, --address=-
reads one or more logical block addresses from stdin. These may
be comma, space, tab or linefeed (newline) separated. If a line
contains "#" then the remaining characters on that line are
ignored. Otherwise each non separator sequence of characters
should resolve to a decimal number unless prefixed by '0x' or
'0X' (or has a trailing 'h'). At least one address must be
given.
-d, --dummy
prepare for but do not execute the SCSI REASSIGN BLOCKS command.
Since the REASSIGN BLOCKS command is essentially irreversible,
paranoid users may wish to check the invocation of this utility
before reassigning defective blocks on a disk. Useful with '-vv'
for those who wish to view the parameter block that will accom‐
pany the command.
-e, --eight=0 | 1
when value is 1 then it sets the 'LONGLBA' flag in the command
indicating that the addresses in the associated parameter block
are 8 byte quantities. When value is 0 then it clears the
'LONGLBA' flag in the command indicating that the addresses in
the associated parameter block are 4 byte quantities. If this
option is not given then 4 byte quantities are assumed unless
one of the address is too large.
-g, --grown
use the SCSI READ DEFECT DATA (10) command to determine the num‐
ber of elements in the "grown defect list". When this option is
given there is no reassignment of blocks (i.e. this utility is
passive). When this option is given then the --address= option
is not permitted. See the discussion below concerning the rela‐
tionship between reassigned blocks and the grown defect list.
This list is sometimes referred to as the GLIST.
-h, --help
output the usage message then exit.
-l, --longlist=0 | 1
sets the REASSIGN BLOCKS cdb field of the same name to the given
value. Only 1000 addresses are permitted so there should be no
need to specify a value of 1. The short list variant restricts
the parameter block length to 2 ** 16 bytes (i.e. about 16000 4
byte addresses or 8000 8 byte addresses). Added for complete‐
ness.
-p, --primary
use the SCSI READ DEFECT DATA (10) command to determine the num‐
ber of elements in the "primary defect list" which is estab‐
lished during the manufacturing process. When this option is
given there is no reassignment of blocks (i.e. this utility is
passive). When this option is given then the --address= option
is not permitted. This list is sometimes referred to as the
PLIST.
-v, --verbose
increase the level of verbosity, (i.e. debug output).
-V, --version
print the version string and then exit.
NOTES
Note that if the ARRE field (for reads) and/or the AWRE field (for
writes) are set in the "Read Write Error Recovery" mode page then
recoverable read and/or write errors cause automatic reassignment of
the defective block. The PER bit in the same mode page controls whether
a RECOVERED ERROR sense key is reported on not (PER=1 implies do
report). Irrespective of the ARRE, AWRE or PER field settings, the
error counter log pages reflect any errors (recovered or otherwise).
Whenever a block is reassigned, a new entry is added in the "grown"
defect list. Apart from doing selftests (see sg_senddiag or smartmon‐
tools) regularly, monitoring the grown defect list of a disk is a rea‐
sonable metric of its health. If the grown list starts growing quickly
that is an ominous sign. The best grown defect lists are empty ones.
The number of elements in the grown defect list can be viewed with the
--grown option. The contents of the grown defect list can be viewed
with the 'sginfo -G' utility.
If an unrecoverable error is detected at a logical block address then
REASSIGN BLOCKS is needed to reassign the block. Also if the ARRE
and/or AWRE fields are clear and a recoverable error is detected then
the logical block in question may be reassigned with this utility (oth‐
erwise the error counter log pages will continually be incremented for
each recovered access).
The number of blocks held in reserve for the purposes of REASSIGN
BLOCKS is vendor specific and may well be limited to the zone within
the media where the original (defective) block lay. When this number is
exhausted subsequent invocations of this utility may result in a sense
key of hardware error and an additional sense of 'No defect spare loca‐
tion available'. The next step would be to reformat the disk (or get a
replacement).
The SBC-2 draft standard (revision 16) notes that when multiple
addresses are given to the SCSI REASSIGN BLOCKS command and there is
some failure at one of the later addresses then all addresses prior to
that have already be reassigned. Care should be taken in such a case.
Re-executing the command with the same addresses will cause the earlier
addresses to be reassigned again. At some stage the disk will run out
of reserved locations. So unless a large number of addresses are
involved it may be safer to reassign them one address at a time.
EXIT STATUS
The exit status of sg_reassign is 0 when it is successful. Otherwise
see the sg3_utils(8) man page.
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 2005-2009 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO war‐
ranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR‐
POSE.
SEE ALSO
sg_format,sginfo,sg_senddiag(all in sg3_utils), sdparm(sdparm), smart‐
montools(internet, sourceforge)
sg3_utils-1.27 April 2009 SG_REASSIGN(8)
[top]
List of man pages available for Scientific
Copyright (c) for man pages and the logo by the respective OS vendor.
For those who want to learn more, the polarhome community provides shell access and support.
[legal]
[privacy]
[GNU]
[policy]
[cookies]
[netiquette]
[sponsors]
[FAQ]
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
|
|
Vote for polarhome
|
