READ(2) Linux Programmer's Manual READ(2)NAME
read - read from a file descriptor
ssize_t read(int fd, void *buf, size_t count);
DESCRIPTIONread() attempts to read up to count bytes from file descriptor fd into
the buffer starting at buf.
On files that support seeking, the read operation commences at the cur‐
rent file offset, and the file offset is incremented by the number of
bytes read. If the current file offset is at or past the end of file,
no bytes are read, and read() returns zero.
If count is zero, read() may detect the errors described below. In the
absence of any errors, or if read() does not check for errors, a read()
with a count of 0 returns zero and has no other effects.
If count is greater than SSIZE_MAX, the result is unspecified.
On success, the number of bytes read is returned (zero indicates end of
file), and the file position is advanced by this number. It is not an
error if this number is smaller than the number of bytes requested;
this may happen for example because fewer bytes are actually available
right now (maybe because we were close to end-of-file, or because we
are reading from a pipe, or from a terminal), or because read() was
interrupted by a signal. On error, -1 is returned, and errno is set
appropriately. In this case it is left unspecified whether the file
position (if any) changes.
EAGAIN The file descriptor fd refers to a file other than a socket and
has been marked nonblocking (O_NONBLOCK), and the read would
EAGAIN or EWOULDBLOCK
The file descriptor fd refers to a socket and has been marked
nonblocking (O_NONBLOCK), and the read would block.
POSIX.1-2001 allows either error to be returned for this case,
and does not require these constants to have the same value, so
a portable application should check for both possibilities.
EBADF fd is not a valid file descriptor or is not open for reading.
EFAULT buf is outside your accessible address space.
EINTR The call was interrupted by a signal before any data was read;
EINVAL fd is attached to an object which is unsuitable for reading; or
the file was opened with the O_DIRECT flag, and either the
address specified in buf, the value specified in count, or the
current file offset is not suitably aligned.
EINVAL fd was created via a call to timerfd_create(2) and the wrong
size buffer was given to read(); see timerfd_create(2) for fur‐
EIO I/O error. This will happen for example when the process is in
a background process group, tries to read from its controlling
terminal, and either it is ignoring or blocking SIGTTIN or its
process group is orphaned. It may also occur when there is a
low-level I/O error while reading from a disk or tape.
EISDIR fd refers to a directory.
Other errors may occur, depending on the object connected to fd. POSIX
allows a read() that is interrupted after reading some data to return
-1 (with errno set to EINTR) or to return the number of bytes already
SVr4, 4.3BSD, POSIX.1-2001.
On NFS filesystems, reading small amounts of data will update the time‐
stamp only the first time, subsequent calls may not do so. This is
caused by client side attribute caching, because most if not all NFS
clients leave st_atime (last file access time) updates to the server
and client side reads satisfied from the client's cache will not cause
st_atime updates on the server as there are no server side reads. UNIX
semantics can be obtained by disabling client side attribute caching,
but in most situations this will substantially increase server load and
SEE ALSOclose(2), fcntl(2), ioctl(2), lseek(2), open(2), pread(2), readdir(2),
readlink(2), readv(2), select(2), write(2), fread(3)COLOPHON
This page is part of release 3.63 of the Linux man-pages project. A
description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 2013-02-12 READ(2)