drd-deactivate man page on HP-UX

Man page or keyword search:  
man Server   10987 pages
apropos Keyword Search (all sections)
Output format
HP-UX logo
[printable version]

drd-deactivate(1M)					    drd-deactivate(1M)

NAME
       drd  deactivate	 -  If	drd  activate has been utilized to invoke set‐
       boot(1M) and set the clone as the primary boot path but the system  has
       not yet been rebooted, this command can be used to "undo" the drd acti‐
       vate and set the original system image to be  the  primary  boot	 path.
       This  command will always set the primary boot path to the active (cur‐
       rently booted) system image.

SYNOPSIS
       option_file]

DESCRIPTION
       The drd deactivate command invokes the setboot (1M) command to set  the
       primary boot disk to the active (booted) system image.

       Note: is a mechanism for "undoing" a drd activate.

   Options
       recognizes the following options:

	      Displays the usage message.

	      Sets preview mode.

	      Decreases	 the verbosity level by one each time it is specified.
	      For example,
		     will reduce the verbosity from the default value of 4  to
		     2.	  If  both  and	 are included on the command line, the
		     effective verbosity is 2. The minimum verbosity level  is
		     0.	 (See also the option).

	      Increases	 the verbosity level by one each time it is specified.
	      For example,
		     will increase the effective verbosity  from  the  default
		     value  of 4 to 5. If both and are included on the command
		     line, the effective verbosity is 3. The maximum verbosity
		     level is 5.  (See also the option).

	      Displays the list of possible
		     (extended) options.

	      Sets  the	 extended  option  to a value. See Extended -x Options
	      definitions below.

	      Gets the extended options from a file.

   Extended -x Options
       recognizes the following (extended) options:

       Usage: Basic
	      This is the alternate boot disk.	The alternate boot  disk  must
	      be specified as a block device file.

       Usage: Basic
	      This  is	the  High  Availability alternate boot disk.  The High
	      Availability alternate boot disk must be specified  as  a	 block
	      device file.  High Availability alternate boot disk is supported
	      only on Itanium-based architecture and for PA-RISC systems  that
	      support hardware partitions.

       Usage: Basic
	      This  is	the  path to the log file for this command.  Each time
	      DRD is run, this file will grow larger.  This  can  be  changed,
	      for  example, to a month-specific location for easier archiving,
	      off-host backup, and rotation.

       Usage: Basic
	      Specifies the level of message verbosity in the  log  file  (See
	      also -x verbosity).  Legal values are:

	      Only ERROR messages and the startingending BANNER messages.

	      Adds WARNING messages.

	      Adds NOTE messages.

	      Adds  INFO  messages (informational messages preceded by the '*'
	      character).

	      Adds verbose INFO messages.

	      Adds very-verbose INFO messages.

       Usage: Basic
	      If true, run this command in preview mode only  (i.e.,  complete
	      the  analysis phase and exit; no changes are committed to disk).
	      Setting this option to true has the same effect as specifying -p
	      on the command line.

       Usage: Basic
	      Specifies the level of stderr verboseness:

	      Only ERROR messages and the startingending BANNER messages.

	      Adds WARNING messages.

	      Adds NOTE messages.

	      Adds  INFO  messages (informational messages preceded by the '*'
	      character).

	      Adds verbose INFO messages.

	      Adds very-verbose INFO messages.

		     Note:  The '-v' option is equivalent to  increasing  ver‐
		     bosity  by	 1  (e.g., from 3 to 4) and the '-q' option is
		     equivalent to decreasing verbosity by 1.	The  '-v'  and
		     '-q' options can be used more than once.

   Return Values
       returns the following values:

	      Success.
	      Error.
	      Warning.

   Examples
       To restore the active (booted) system image as the primary boot disk:

       To  restore  the	 active (booted) system image as the primary boot disk
       and set a different disk as the alternate boot disk:

	      For 11iv2:

	      For 11iv3:

       To display all extended options:

AUTHOR
       was developed by Hewlett-Packard Development Company, L.P.

FILES
       Log file.

SEE ALSO
       drd(1M),	  drd-activate(1M),   drd-clone(1M),	drd-mount(1M),	  drd-
       rehost(1M),  drd-runcmd(1M),  drd-status(1M), drd-umount(1M), drd-unre‐
       host(1M)

       Dynamic	  Root	  Disk	  Administrator's    Guide,    available    at
       http:docs/hp.comenDRD.

							    drd-deactivate(1M)
[top]

List of man pages available for HP-UX

Copyright (c) for man pages and the logo by the respective OS vendor.

For those who want to learn more, the polarhome community provides shell access and support.

[legal] [privacy] [GNU] [policy] [cookies] [netiquette] [sponsors] [FAQ]
Tweet
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
Vote for polarhome
Free Shell Accounts :: the biggest list on the net